Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi,
is it possible for a central device to connect to a peripheral device directly (without using nrf_ble_scan_init( ), nrf_ble_scan_filter_set( ), nrf_ble_scan_filters_enable...
Hello,
I am trying to write some code that sets the BLE Tx power on the nRF52833 SoC.
I have based my code on the sample example code provided at C:\Zypher\v1.7.0\zephyr...
We're using the read authentication trigger to detect when a characteristic is being read, so we can update the value before a read. Is it possible to have a read with zero...
Hello,
at the beginning I want to state, that I have read all the tickets with similar issue, but still can't find any solution to my problem, that's why I'm creating...
Hi!
I was controling a little vibration motor with a mosfet which is activated by a nrf52840Dongle pin. I was using pin 0.17 and it worked pretty well, but now I am trying...
Dear reader
We want to use the floating point unit (FPU) in our project
We are building using the IAR compiler (8.5.x)
We'd like to use the hardware acceleration ...
Hi.
We are working on a project which uses nrF9160DK and nRF5340DK, which works fine on this last one. The problem is that when I tried building on the 9160 using nRF Connect...
Hello.
I read this article
https://devzone.nordicsemi.com/f/nordic-q-a/66914/uart-current-consumption
I did my testing with ble_app_uart from SDK 17.0.2 on a nRF52832...
Dear all,
I am now using several pairs of nrf52840DK and nrf connect sdk v1.7.1,and using llpm(low latency packet mode) to send data.
In our system,there are four pairs...
Hi,
I have an issue where sometimes after a restart of our device the nRF hangs on either: ble_dfu_buttonless_async_svci_init() or ble_dfu_buttonless_init(&dfuButtonlessService...
Hello all,
I have 2 problem that I can not understand why.
1) Now cdc_acm isn't working anymore, but until 2 days ago it was working perfectly. I didn't change nothing...
Hi, I'm developing an application tracker device using 2 libuartes, pwm, ble and now I am going to approach reading battery level. After I research on dev zone but I only...
There is already a case on github:
https://github.com/zephyrproject-rtos/zephyr/issues/44586
But essentially we see an issue with nrf5340, where we get random crashes...
HI,
I have tried to read the I2S data by using nrf5340 and I successfully did that. Now, I want to work on the sample with BLE. for that I have made some configurations...
