FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
Hi there,
I have just started the NCS Fundamental Course and I am stuck on Exercise 2. There are two problems that I am facing.
1) I have an nrf9160dk board. so if I compile...
Hello, I am trying to read data from the sensor using I2C, I have the nrf9160 on an Icarus board https://www.actinius.com/icarus .
I tried following this guide: https:/...
Hi Nordic Team,
I see that I am supposed to GND 2 of the SPI lines and drive the CSN high to use it in GPIO control only mode. We wanted to TP out the SPI bus for the FEM...
I am trying to send value 0x75 using I2c but when i check the value using logical analyzer i found it 0x74. and when i tried to send 0x77 i found it equal to 0x76. any help...
I am currently working on a project in which I want to transmit audio wirelessly from one nRF chip to another. Currently I am using the nRF Dongle to act as the transmitter...
Hello Everyone,
I am using NRF52833 in my project and I have implemented one service named borrower. The code details are in the attached in the files. When I open nrfconnect...
Hi Nordic,
I have 2 nrf52840 hosts running gazell HOST mode, and 1 device running gazell DEVICE mode. My question is, when device sends data to host, will both 2 hosts receive...
I connected to the cloud with the factory installed fimrware ( thingy91_1.4.0_production_final, mfw_nrf9160_1.1.1).
In the "Firmware Updta History" it shows: "To use the...
Hi,
I'm working on optimizing the download time of data via bluetooth with the nrf52820 android and IOS phones. To do this, I chose to play with the connection parameters...
Hi,
I am using a j-link EDU to program our devices. I use nRFConnect 3.11.0 and prorammer 2.3.3. My problem is that I don't get the j-link device up in the programmer tool...
Hello,
I am testing out a custom board with the nRF52840 and I am trying to interface with an I2C slave using the chip. Right now I am just trying to see if I can find the...
Hello,
I was not able to see the device in select device drop down box in nRFconnect programmer app. My aim is to program BLE soft device into the DK.
OS: Windows...
Dear Forum,
I have successfully compiled and pretested the direct test mode firmware for SDK_17.0.2.
The UART is shown as /dev/ttyUSB0 in my Ubuntu 20.4 Linux system....
