I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Hi, I have been getting randomly errors status from pmic measurements including status 64 (trickle timeout, I presume). Do you have any sample code to handle errors as per...
This is a custom board with nRF54L15. I have the following peripherals connected:
I2C30 SDA:P0,02 SCL:P0.03
I2C20 SDA:P1.13 SCL:P1.12
UART00 TX:P2.02 RX:P2.00
I also...
Hello,
Currently designing in the npm1300 into a project and want to understand better the difference between the LDO and the load switch. In the example schematics the...
Hi
Since the Vout setting range is 1V~3.3V, and the datasheet Figure 39 show the dropout voltage is ~60mV(0.06V)
Why datasheet LDO electric spec. show the VIN need larger...
Folks,
We have been developing a product to use the nrf51840 Dongle. Idea being to solder it to a mother board and as it's pre certified we don't have to go through RF certification...
Hello, I'm building the sample Measure battery voltage on a custom board, and I have an error voltage: setup: -134 at runtime. The overlay file is configure as explained in...
I want to implement OTA (Over-the-Air) updates using Thread on the nRF52840 DK board.
Are there any sample codes or references available for achieving this with Thread?
Hello,
I'm trying to use nRF9160 Development kit and it is not showing up in connected devices view in VS code.
Switch position is correct(nRF91) on the development...
I am using v3.0.2 SDK, nrf52832 DK, and I am learning academy.nordicsemi.com/.../ . I encountered a problem in step 4.2:
Please help me find out how to debug
With the NRF_CLOUD_MULTI_SERVICE sample, we'd like to set the GNSS location tracking sample interval to 2s or even 1s.
But we found that the actual time will be about 25s...
Hello everyone, I need to attach a QSPI memory to an NRF54L15 module. I am led to believe that this should be supported out of the box but cannot understand how to use the...
Hello everyone,
I am working on a project where I need maximum range and TX power, since my Bluetooth device will be implanted the signal is strongly attenuated I need maximum...
Hi,
We are evaluating the NRF9151 for live tracking purposes. While testing with the nRF9151-DK we noticed the we had tracking fallouts using AT#XGPS=1,1,1 both during driving...
Hi everyone,
After the latest update of the nRF Connect SDK plugin for VS Code (2025.4.106), we've seen this pop-up appear. We are using v1.8.0 and now we are not able to...
