Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hi,
I need to write a 32-bit value to an NVM flash page whenever my code hits an assert failure. This failure can occur anywhere in the code - my application, the Nordic...
Hello,
I'm working on a circuit which has a pin connected to a pull-up resistor, using the nRF52 DK and SEGGER Embedded Studio 5.20 to develop the software.
This pin is...
Hello everybody, I am using Zephyr with the nrf52840-dk device. I would like to store the DTLS credentials with a secure way. I don't want to be part of the code and thus...
I have been testing out HTTPS with the http_application_update .
I have been able to successfully setup a TLS 1.2 connection, but I was seeing a lot of "Peer closed connection...
Hello
I would like to modify my Transmission Parameters of my Thread network. According to the CoAP protocol ( https://tools.ietf.org/html/rfc7252#section-4.8 ), it is possible...
Hi Dev Team,
I am trying to measure the low power performance of the nrf9160.
For this, I tried to use the "system_off" example in the folder : C:\Users\adeel\ncs\v1.4...
Hi,
I'm trying to alternate between the beacon sample and the central sample in one application. It builds and initiates, the connection example from central is functioning...
Hello everyone, this is my first time participating in the forum. I am a very new hardware and firmware developer (this is my first job in the industry of iot). I have chosen...
We are currently evaluating external memory on the NRF52840 and are trying to use external memory within the memory space of the processor (XIP). We are aware of the erratas...
Hi, I am using nrf52840 as a peripheral. How can I use more than 1 uart(1 for GSM,2nd For GPS, and 3rd for show data in PuTTY). Which pins I can use for this? and how? any...
Hi,
We have a requirement where we need to store some application parameters (Eg. APN name ) in the nrf9160 flash. This parameters will be storing during production time...
Hi,
1. I was trying to measure the Bluetooth throughput of nRF5340PDK using the sample from ...\ncs\v1.4.0\nrf\samples\bluetooth\throughput, but from what I see in the requirements...
Hi Support team,
A customer would like to use an external 32kHz TCXO to nRF52840. As the picture shown, the original 32kHz crystal and the loading capacitors are removed...
Hi,
I using the nrf52840 EVB(pca10056), there's no nrf21540 connect, but in our design we will using the nrf52840 + nrf21540.
And I build the radio test example with...
