Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello,
I'm experiencing a disconnection problem on several BLE Mesh networks. My topology is 1 client with an average of 60 servers, for all networks. Client is connected...
Hi guys,
I have the same issue as coca1989 had 2 years ago . Did anybody found a solution?
I am using health model and simple message model. Client and Provisioner are...
Hi,
Iam working on a project based on Ble Mesh, Iam using nrf5_SDK_for_Mesh_v4.2.0_src. Iam trying to form a BLE Mesh network and control the light bulb. I went through...
Hello Devs,
I am facing an difficult time to write a custom opcode to a QSPI flash memory. where I am trying to read the manufacture ID, it requires send the OP code + Address...
Hi, We are looking for a Suitable wireless technology for Video transfer(Video Transmitter and receiver)
Main Constraint: - From Power Up-->Boot-Up time of Wireless transmitter...
Hello,
We are looking for a 2.4Ghz supported module with Programmable Frequency Deviation. Is there a product that we can consider from Nordic Semiconductor for this?...
Hi, We are working with integrating LoRa to our nRF52840 with BLE and FreeRTOS. To be sure that LoRa worked as expected, we configured and tested LoRa on nRF52840 dk and observed...
Hello,
I'm using nrf52840 and i would like to ask if it possible to use the I2C bus without external pullups. I mean, i would like to avoid using external pullups
is there...
I am using a NRF52840 DK with a SoftDevice S140 6.1.1. I have also flashed the secure ble bootloader on the device.
I have been using the nrfprog command line tools within...
Hello,
Got the MQTT_SIMPLE to work and the sensor samples from zephyr also, however, how can i mix the 2 to have the mqttsimple with some gpio and i2c sensor ? how will...
Hi
I have installed every requirement for the device. I want to know how to run the blinky example on the device. I can not find the SDK which has the example plus can I...
Hello, I'm currently developing a PS2 code to read the inputs of a mouse and transmit it over BLE, nrf_delay_us() is giving me a fatal error every time according to debug...
Hi,
I am trying to implement Generic HID that can transmit/receive data like CDC using the generic HID example source of nRF52820 SDK 17.0.2.
But I can't do both sending...
Hello everyone,
I'm a fresher of nRF52833. I'm facing a problem like this:
I want to read some information in Terminal but In my product I only have USB I/Os (D+ D-)....
