I can get right value when I chose QDEC_SAMPLEPER_SAMPLEPER_512us in slow application ,but in my application my max data rate is more than 2k, so the QDEC value is less than...
nrf51822 SDK 9.0
iphone 6plus System version IOS9.2
When the phone receives the QQ message "static void notif_print(ble_ancs_c_evt_notif_t * p_notif);" can execute.
but...
Hi..... This is Venkatesh. I am using nRF52-DK Evaluation kit. This is my first question posting here. It is pleasure to have an account to share my knowledge and get the...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello - I have the exact same question as proposed in this thread - I am wondering if there has been any change in the 3 last years since it was posted.
In a nutshell, we...
Hi
I have a code previously can be built in NCS 2.91:
However, when I use the new NCS 3.01, it can not be built, the error is:
Could you please help me figure out...
I am currently working on the secure_bootloader example (pca10056_s140_ble) for the nRF52840 DK board and am encountering an issue with updating the OTA application. I have...
Hello, I connected my (working) PPK2 and opened the PowerProfiler. Immediately, a "DFU needed" message popped up.
I DFUed the PPK2, and in the logs, it wrote DFU successfully...
What should be format of USER Certs for Matter factory data?
CONFIG_CHIP_FACTORY_DATA_CERT_SOURCE_USER =y
CONFIG_CHIP_FACTORY_DATA_USER_CERTS_DAC_CERT = "certs/Chip...
Hello, I have an application developed with the nRF9161 DK board, which essentially consists of a GPS tracker that acquires a position every x time and sends that same position...
hi support team,
i have customer is developping mesh.
customer is trying to sniffer the message when i pressed the buttoon on demo mesh_light.
i have two questions on...
NCS 2.9.1
NRF52840
Sysbuild but with only a single image (no bootloader)
I've been trying to figure out how to change the merged.hex output and how to perform additional...
Hello DevZone,
Is it possible to support Matter over Ethernet and Matter over Wi-Fi at same time?
Since there are many Ethernet chips support in Zephyr.
Seems that the...
Hi,
I'm looking to continuously sample the ADC at a high sample rate with rotating buffers.
I found an example code that matches what I need with the older SDK for...
We are using nRF5340 with nRF7002 on our custom board. Our application requires:
Wi-Fi (via nRF7002)
Thread (via nRF5340)
DFU over Wi-Fi
We are concerned...
We have peripheral, and we want to connect it using NRF 52840. when we are bonding this using nrf connect app we get a pop up with random key and using pair we can pair with...
I'm using the nRF9160 with the LIS2DH accelerometer and SDK version 2.5.2 . In my hardware setup, INT1 is connected to GPIO 0 and INT2 to GPIO 1 . I'm configuring both interrupt...
Hello,
I am currently using the `AT%XICCID` to obtain the ICCID of Hologram eSIMs. The output of some of these eSIMs are just the raw 20 digit ICCID with no ending checksum...
Hi,
I’m looking for your recommendations on a suitable conformal coating for an application subject to high humidity. The goal is to mitigate any potential risk of short...
