Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
The CPU runs the main thread every 3 seconds, and for the remaining time, it enters the idle thread. However, after entering the idle thread, it doesn’t save power.
But...
Hi guys,
we are planing to use the nRF52820 as BLE proxy to UART/SPI. It shall receive data from a host controller via UART/SPI and forward it via BLE to a smart phone....
I recently purchased an nRF52840 DK (v3.0.0) to use with my custom nRF9160 boards for firmware loading, debugging, and loading certificates for nRF Cloud. While I can successfully...
For connecting an external TCXO reference, we need to know the specification for the slew rate and levels (Vhigh/Vlow). In the product specs, the clock accuracy is defined...
Hello. I'm newbie with the NCS environment so tell me if I'm saying nosense. I use the nrf connect extension in vs code ide. (SDK: v2.7.0 toolchain: v2.7.0)
I want to...
I am working on new project setup. I have copied a sample blinky project from nRF connect SDK(C:\ncs\v2.7.0\zephyr\samples\basic\blinky) and board I selected in Build configuration...
Hi,
I'm following this "Getting started with Nordic's Secure DFU bootloader, a step by step guide" ( https://devzone.nordicsemi.com/guides/short-range-guides/b/software...
In our application build with SDK 2.7.0 on a NRF52840 chip, we get an assert if we update the TX_Power for the connections.
If the bluetooth has made connection, we update...
Hey everyone!
I’m working on a project using Zephyr with an nRF5340 board and trying to configure UART1 completely from scratch. Most tutorials I’ve found only cover UART0...
Dear Nordic Support Team,
I am working with the nRF52840 and need to configure the SPI peripheral in Zephyr to operate without DMA.
I’ve encountered a few problems:
...
I am able to update the app core successfully from an external flash partition via the `mcumgr` desktop tool. However, this is not working for the net core.
It successfully...
I would like to create a thread based sensor and use Apple/Amazon/Google smarthome hubs as the OTBR. How do I commission a thread device (not a matter device) to these hubs...
Hello,
I'm working with Zephyr and using MCUBOOT as bootloader.
Due to HW design I have to set and hold a gpio as fast as possible when the application boots (to prevent...
Hello,
We're seeing an error that only happens after a cold reboot (unplugging the battery and replugging it) and it happens inside the bootloader while trying to open the...
Dear all:
I used this command to build light switch for 5340DK:
west build -p always --build-dir nrf/samples/matter/light_switch/build -b nrf5340dk_nrf5340_cpuapp nrf...
