This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Hi experts,
I have a problem with programming NRF5340 SoC when using the NRF-Programmer tool. About our board, we use PCBA instead of NRF5340 Dev-Kit.
Step1: My coworker...
I'm moving an application from NCS v2.0.2 to NCS v2.1.0
Everything compiles properly in v2.0.2.
I think I've converted all of the pin definitions properly from the v2...
Hello,
we are using nRF9160 as Bluetooth host together with the Mcumgr Gatt service. We would like to be able to perform FMFU update using the Mcumgr library. We have verified...
Hi:
After downloading the sdk, I installed the compilation environment on my laptop and successfully compiled the at_client project. However, after the same installation...
I want to implement a sophisticated peripheral that implements a keyboard, mouse, and raw HID interface via USB and BLE.
I haven't found composite HID examples for USB or...
Hi,
When I try to build the ESPI sample using west I'm getting the following error:
Can you please let me know what the error is? I tried looking up the issue, but couldn...
Hello Nordic Team,
While going through this page on peripherals used by Softdevice https://infocenter.nordicsemi.com/topic/sds_s140/SDS/s1xx/sd_resource_reqs/hw_block_interrupt_vector...
Hi guys,
I want to send 'a' characters via the uart1 of the nRF52840-DK. I cut the short on the SB6 jumper to disconnect LED 2 from P0.14, which also happens to be TX of...
Hi DevZone
I just want to ask if one can use the nPM1100 with the unregulated output to the nRF9160 (which can take 3-5.5V), and the regulated output the other peripherals...
We try to get audio samples form analog or digital MEMS microphone to nrf54840 RAM memory with low power consumpion at 32kHz rate. We consider to use internal SAADC, PDM or...
hi, I want to use PPI function for timer trigger GPIOTE,
when timer interrupt comes, my output pin will toggle, but I find my code doesn't work, I think it is GPIOTE mistake...
I am trying to run the nrf/samples/bluetooth/peripheral_lbs example for the nRF5340-Audio-DK using nRF SDK v2.1.0. I am using the following command to run the example:
west...
We have a product on the market that uses the nRF24 and a PIC, chosen primarily for it's cost and rapid development time. We are now looking into using a nRF52 to replace...
My system details:
Ubuntu 20.04.04 LTS
Visual Studio Code 1.70.2
NCS 2.0.2
nrfutil version 5.2.0
Toolchain Manager v1.1.3
I'm trying to build my project, but...
Hi,
I'm developing my log system in a project with a secure partition with TF-M. I am following this log system design document . In my project I have, as a test, the following...
