Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
Hi,
I recently started with nRF52840-DK, Zephyr and nRF Connect SDK (v. 1.9.1). I want to test extended advertising. Since there is no example of "pure" extended advertising...
Hi Nordic team,
I am working on a project with one central and several peripheral BLE devices. The peripherals are moving randomly, is it possible to detect the event...
Hi, recently testing nrf9160 SMS example, but seems not working in both Send/Receive
I confirm that SMS is valid in my SIM Card, I put it in my mobile phone and verified...
Can you please explain how the %XCOUNTRYDATA command can speed up network selection in a new location? Does the modem perform a general scan on all bands to determine the...
hello , I am working spi with softdevice(i.e., bluetooth). here spi master is nrf52 and spi slave is ad9837. the spi interface code works fine without soft device(i.e.,ble...
Hello, we are developing a keyboard with two types of connections, via USB and Bluetooth using the nRF52833 chip.
We have all the firmware developed in Arduino since it...
Hi,
I am trying to compile the cfb sample as provided in v2.0.0.
my overlay file is as follows
and my prj file
When I try to build, I get the following error...
is there a way to change the target device to nRF52820 (PCA10100) in segger embedded studio? initially configured to nRF52832 when we started our setup (nRF Connect Desktop...
I want to design a general module. Is it feasible to design the schematic diagram in this way?
1.VDDH is powered by external power supply, is that ok?
2.VBUS is powered...
Hi,
We want to check how changing system voltage affects on GPS reception, for that we need to know the RSSI of each satellite the model use.
I know I can get the C2N...
This is in reference to: devzone.nordicsemi.com/.../getting-started-with-nordics-secure-dfu-bootloader
On step B1, it says: " Next step, inside SDKFolder\external\micro...
Hi,
I'm working on a project where the NRF52840 chip is connected to multiple peripherals (4 of them) through SPI. The hardware has been designed in a way that each peripheral...
Hi, I am using the ant_plus/ant_bpwr/bpwr_rx code as a reference to capture power data from an SRM power meter. I am at the point where I get the following messages, which...
Title says most of it. I'm wanting to perform an OTA DFU of an nRF52840 running NCS 2.0.0 using my android from either the nRF Connect Device Manager or nRF DFU app. There...
This is my first time developing for Nordic processors. I am using Zephyr 3.0.99 with the nrf52810 on a ublox BMD-330 eval board. I connected a W25X20CL 2M-bit chip via the...
