Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hello,
I am using nRF52840 DK to build ble_app_interactive.
Now I have device with NUS,I can connect to device using ble_app_interactive.
I have added NUS into...
Hi,
I am successfully connected to central and peripheral, Now i want to push-button(nRF52810, custom board) and this information should be received by central(nRF52832...
Hi,
nRF5340 Audio Application working very well while im using 2 nRF5340 board.
But i wonder, how can i connect to the other brand's board using nRF5340 Audio DK ?
I...
Hi,
we got a nrf5340 audio DK recently, when want to build example code for it, I get this message：
warning: attempt to assign the value 'y' to the undefined symbol HW_CODEC_CIRRUS_LOGIC...
Hello!!
I have explored extended advertising using both nRF5 SDK and nRF Connect SDK. Using nRF5 SDK, it is not possible to advertise 1650 bytes in an extended advertising...
Hello,
SDK17.2, keil5,nRF21540-DK
my project use i2c and spi, but got error:
Error: L6200E: Symbol SPIM0_SPIS0_TWIM0_TWIS0_SPI0_TWI0_IRQHandler multiply defined (by...
Hello,
SDK17.2, Keil5, nRF21540-DK,
when change DCCH to 3.3V as above codes in main first,
(1). the uart will can not work ,
(2). change pin to high voltage as follow...
I get some message from Nordic.I want to give my IQ sample to MQTT.i see that they give me information about a API of MQTT.
But i can't use it,can you give me the more information...
Hello !
What extra field need to be included ti MAXLEN calculation in case of Ieee802154_250Kbit radio ?
CRC , len ? I try to limit total amount of received bytes but...
Hi,
I have nrf52832 dK and know how to configure them in code.
I have studied BLE supports the LE 1M phy and LE 2M phys from BLE core specifications.
I know about the...
Hi devzone, I've had UART communication problems between nRF52 and a BG96 modem for a long time.
today I added a pull down resistance on the rx of the nRF52 and it works...
Good day,
I am currently developing with two NRF52840 DK boards, and I also have two NRF Dongles. On a dongle a sniffer for ZigBee. I am working with SDK 3.2. This is my...
Hi i want to make a low power delay ms (blocking) function for nrf52805 without softdevice and without NRFx, just writing to the registers.
The RTC1 events_tick never...
