hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Hi,
I am working with the nRF52832 DK. I want to program a couple of ICs with SPI every 2 ms. I have successfully configured the nRF as SPI master and I start the SPI transfers...
Hi All,
I wanted to look at the power profile for my nRF52840 dongle, I installed nRF connect and installed the Power Profiler. But as I want to the option to connect the...
Hi，
Hello everyone, I have encountered a problem in the pairing and bonding process of BLE.I use two NRF52832 development boards, one acts as a slave and the other acts...
We use FreeRTOS with nRF SDK driver library. The driver library is working well because it doesn't dynamically allocate any memory. So I can simple take entire memory block...
I'm facing some problems when trying to run my custom board on standard batteries.
The device boots fine but when the LTE modem connects I get a reset.
The nrf9160 is...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v1.9.1
I need high performance data transfer, so I review throughput sample. C:\Users\user\ncs\v1.9.1\nrf\samples\bluetooth\throughput...
We are using nRF9160 (Development Kit), SDK 1.9.1 board with "serial lte modem" firmware. We are trying to get AGPS coordinates (using an external antenna), but for some reason...
In the nrf5340 development process.I compile an app core hex from project A and a net core hex firmware from another project B. what method can I quickly obtain a merged firmware...
Hi,
I'm trying to get the maximum possible throughput from a peripheral device, sending notifications to a central. I compare the throughput between 2 PCA10040 boards...
Hi,
I'm using s140 trying to connect up to 8 devices to windows BLE adapter and BluetoothLEDevice object, I have 2 problems,
1- the maximum throughput with different configurations...
Hi All!
I am using Segger Embedded Studio and nRF5_SDK_v15.0.0 .Available kits for testing are nrf52833DK and rak4630(nrf52840).
We want to test nRF52833 support on long...
Both NRF were programmed thru USB NRF connect for Desktop programmer.
Both NRF are running the same soft properly.
To demonstrate the final look and put the dongle in...
Hello,
In my project i am using nrf52810 with my custom board for pushing data to UART so i have used UART example code for this but UART pins are connected 20 (TX), 25...
Hi
I'm working on a Zigbee network, and I want to have a few End Devices (ZED) connect to a Coordinator (ZC). And it's fine, I got that working by using the zigbee_default_signal_handler...
hi
i develop software with the nrf52dk, success with program it with nrf command line tool.
now i want to program the application on the nrf52 dongle but with no success...
