Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
We are calling nrf_pwr_mgmt_run which in turn calls sd_app_evt_wait. We set a timer with the app_timer code to wake us up. I verified that the handler is called. However sd_app_evt_wait...
Hi, I want write code on rust, but build system of nrf sdk for nrf5340 too hard for creating bindings, so I decide to create own HAL on rust and embed it in C with BLE stack...
Hello,
I am working on a project that I built using the nRF52DK and then created a custom PCB. The software I wrote works on the DK with a breakout board for the RTC and...
Hi,
I am using a nRF52832,and to begin with I have to erase my memory,so I connect nRF52832 and click erase all.
The result is shown below,I wonder why I can't erase my...
After trials and tribulations I have finally gotten a pulse ox device to work as I needed to. I started with the health thermometer example in the 12.3.0 SDK which is the...
Hi
I tried following the eclipse installation tutorial: devzone.nordicsemi.com/.../
And after a while I got eclipse to handle the Nordic stuff, but when I try to import...
Please find attached several fixes for bugs / incomplete protocol implementation in the MQTTSN stack that we have identified for inclusion in future versions of the SDK. ...
The Thread SDK is pretty awesome! :) However, It does has a bit of a learning curve for me because it only uses UDP instead of TCP.
While searching I found an MQTT variant...
We're developing on a custom NRF53 board. With the I2C bus disconnected from all peripherals, but with external 10k pullups connected, we get the following waveform when attempring...
Hello,
We are working on a research project in Sheridan College to create an indoor positioning system using BLE 5.1’s Angle of Arrival feature. We noticed that nRF52833...
Hi,
I am using the nrf52840dk trying to connect my bike power meter over ANT+, to then forward data to cloud (will be using the nrf9160dk and then the thingy91 once I get...
Dear Support,
I'm evaluating a tiny BLE chip that we can do:
reading multiple three SPI sensors: pressure sensor, accelerometer, and FRAM.
So with your BLE chip...
Hi,
Using 52833 it seems that sometimes the radio quits responding, ie, it is in NRF_RADIO_STATE_DISABLED state and there is
no obvious way to get it out of that state...
Hello,
I'm trying to program the ble_app_uart example program from SDK 17.0.2 in Segger Embedded Studio using softdevice 132 to a custom PCB (with the nRF52832 chip) using...
Hi,
I am using nrf9160 to handle the MQTT protocol and collect the data packets from another microcontroller using the UART interface.
Sending the data to the server using...
