Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello Nordic,
I had to reload a new nrfcloud certificate to my nrf9160DK. An active iBasis SIM card is attached to my nrfcloud account.
I followed these instructions:...
Hi everyone,
I have 1 board normal node(client+server) and 1 board LPN(client+server). I can send message from client of LPN to server of normal node, but i can't send message...
Hello,
I have a design where I am using an nRF52840 along with a SKY66112-11 and am using Zephyr/MPSL for both BLE and Thread. Some questions:
1) The .dts node has pa_gain_db...
Hi,
I was testing the GPS performance of the the thingie91. The default application (asset_tracker) works perfectly, but uses AGPS from the nordic cloud.
The asset_tracker_v2...
Hi all,
We run into a problem where our central product (a remote control) connects to the wrong device. We are using SDK v14.2.0 and softdevice S132 version 5.1.0. At...
Hallo,
I'm using a 52840dongle.
Uart ( PC-Terminal Debugging)
Radio ( reading 51822)
I2C Display
is working well
No i need to write and read data to/from a spi...
I have a serial OLED LCD on my SPI bus on my nrf52840 I want to do periodic LCD refresh by sending it's frame buffer without involving CPU.
I already know how to do SPI...
Hello!
I flashed the light_bulb example(NRF5 SDK v.4.2.0) hex to an nRF52840 Dongle using nRF Connect.
After reset, LED2 lights blue.
I do have an existing Zigbee network...
We have been using ble nus service which is working very well.
There are more than 100,000 bytes of data to be transferred each time.
We were using BLE_NUS_EVT_TX_RDY...
Hi I made some changes in the chat project that is found in NRF Connect SDK and when I build the change project this error occurs
kobj-types-enum.h: No such file or directory...
Hi,
I am writing after searching for an answer in this forum but without success.
I am not sure to understand the purpose of ble_app_proximity_coexist? I understood that...
I'm developing the nRF5340DK, would like to use the P0.04 (AIN0) pin to get the NTC thermistor value. but bind the device is fail.
the parts of the "source code".
/*ADC...
I'm trying to run your direct test mode code on the nrf53. And verify that the uart pins are working correctly. What is the best way to debug and verify this?
gdb seems...
Hi everyone
I'm looking for a way that I use the libuarte example with two UARTEs: one for receiving data, and one for sending data.
I tested serial uartes example in...
