I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Hi,
I'm little confused regarding BLE NUS and characteristics.
I know that the characteristics are used to expose data, but we also have BLE nus which is used to send...
Hello,
I have 2 questions:
1. Could you tell me the current consumption of a nRF52832 running RTC with external 32 kHz crystal and no RAM retention? Is it 1.9 µA?
...
Hello,
I use nrf52840-dk as central_hr and nrf52833-dk as peripheral_hr, examples from NRF Connect SDK.
It works well, but I want to implement reading Device Information...
I got following error when use the Command Prompt feature
After i run "ncsmgr init-ncs" from bash, it shows
$ ncsmgr init-ncs Checking out NCS v1.6.0 ...FATAL ERROR...
Hi,
I'm developing with 52840 DK, trying to add peer manager to another project I've modified from ble_app_uart (basically I've added saadc, SPI, USB and I2C module based...
Hello
I was setting up the nordic thing 91 (1.4.0, 2020.23) using this video https://www.youtube.com/watch?v=xQ7hDzRULJQ&ab_channel=NordicSemiconductor .
Things were...
I'm starting to design a custom board around the NRF52820 using a 3.7v battery and there is no reference circuity for VDDH using Battery/Ext. regulator. Any tips on what I...
Hi,
We are in the process of evaluating coded phy transceiver for our next product. The product is a IoT node which will send sensor data to centralized gateway and will...
I am using nrf_drv_twi_rx to initiate an I2C read transfer but the interrupt isn't fired for the RX transfer when the ulTaskNotifyTake is used, but seems to work without ulTaskNotifyTake...
Hello, I am making a system with 20 peripherals to a central base on nRF52840. I followed the firmware."ble_app_uart__saadc_timer_driven__scan_mode" from NORDIC playground...
Hello, i I am designing a prototype, the goal is to be able to control a small engine. This engine will be activated when a message is received in MQTT. I currently succeeded...
Hello, I developed for my customer, a ZigBee coordinator in last 2019, using nRF5 SDK for Thread and Zigbee v3.2.0. I have now two questions: - is ZigBee 3.0 supported by...
I'm currently working on the nrf52832_qfax_dcdc pcb after adding a few components. I need to route to pins p0.22, p0.23 SWDIO and SWDCLK but am unable to route away from the...
Hello,
I noticed that publishing mqttsn messages with a payload larger than ~255 bytes caused an error in the mqttsn library. I think the problem comes from this definition...
