GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Background : We developing lighting product and planning to use nRF52833 module and we planning to use the latest SDK version that is nRF5 SDK for Mesh v5.0.0. First step...
Hi,
We're doing some testing of mesh protocols and their latencies using the nRF5340 DK. We want to isolate the wireless communication from interference as much as possible...
Our project uses nRF Connect SDK v1.5.0. Two main developers work with the files in very different environments.
I am not sure if this was an accident of initial development...
Hi,
I am currently running a custom bootloader I found that updates via SPI. I have 2 nrf52840 DKs that are programmed as an SPI master and a SPI bootloader. I have been...
After developing with an nRF52 832 DK (pca10040), our code builds and runs fine. But when we try to use the same code on the nRF52840 dongle it does'nt work. We added flashing...
periodic_adv sample is not working with nrf5340dk_nrf5340_cpuapp
it is working for nrf52840dk_nrf52840 after adding CONFIG_BT_LL_SW_SPLIT=y to proj.conf
Here is the log...
My problem is the that on some devices the ScanResult.getDevice() or ScanResult.getScanResult() both return null on some devices but works fine on most.
This is probably...
Hi folks,
I want to calculate the timestamp for which my thingy 52 board was scanning from another thingy 52(may be more than one board). Is there any technique to get the...
I am confirming ADC sampling 420Hz operation by following question.
https://devzone.nordicsemi.com/f/nordic-q-a/69096/1khz-or-more-adc-sampling-rate-over-ble
The source...
Hello,
I am using the nrf9160DK and I am implementing on zephyr.
For my application I need to write to an external flash memory through I2C. I need to write one page at...
Hello
We are using the NINA-B1 on one of our products.
The phone application is working 100% and was very easy to setup.
Till we came to connect our frontend to...
Hi:
we set p21 as Hardware Reset Pin by config UICR.PSELRESET[0] = UICR. PSELRESET[0] = 21
when we use these code to check halt state, but always get DBG_HCSR zero value...
Hello,
I am attempting to install the nRF Connect SDK v1.5 on a Mac Mini with Mac OS 11 with Apple M1 Silicon per the instructions:
https://developer.nordicsemi.com/nRF_Connect_SDK...
We are using the Nordic fork of Zephyr on nRF5340.
Looking at the serial interface peripherals (SPI/I2C/UART), we understand that these have shared resources and only one...
