Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
I have 2 custom made boards.
I took the first board.
I tested low power consumption. And it WAS working.
Made multiple tests on i2c, BLE, GPIO, Flash memory... All worked...
Dear nordic,
when i try to scan in coded phy some times works but after few minutes it fails to scan(that is not capture beacons). some times it fails from starting(that...
Hello,
I have an issue about the NRF9E5 and the external EEPROM.
When I program the external EEPROM sometimes the procedure fails. When I retry the action is impossible...
Hello,
This is Jahnavi. I am having nRF 52 DK boards. I have a doubt that what will happen if we will give power supply from both coincell as well as USB cable?
Is there...
Development environment: SDK V15.2, Soft device S140 V6.1.1
Application status: unmodified, logging level changed from INFO to DEBUG, debug-flag -DDEBUG set during compilation...
Hi,
When I try to install apps in nRF Connect v2.1.0, I get the following error " Unable to install: Unable to download registry.yarnpkg.com/nrf-framework-courses . Got...
Hello !
I got bad time figuring out how we can prevent a Malicious device to corrupt our thread Network and only allow our device to connect to this mesh network.
I am...
I am trying to get the nRF52840 to interoperate with an existing product using the Telegesis ETRX357 Zigbee radio running a Zigbee 2007 PRO stack. For now, I’m using the nRF52840...
Hi,
I'm developing an application on Android based on nRF_UART apk source, but i'm having trouble in connecting to two BLE devices. Actually, i think i could manage to connect...
Hi,
I am trying to use BSP button event to take the system into sleep mode. A long push turns off IO and calls power management shutdown and the same button is configured...
Hello community!
I use the dongle PCA10059 (nrf52840) for my hardware. I already enable -DARM_MATH_CM4 and link library libarm_cortexM4lf_math.a with CMake. I can include...
Hei,
I am following the Install the toolchain section and after running
choco install python
the step does not verify because it does not find pip3.
'pip3' is not...
One of our resellers is requesting a classification code for the RF protocol. We use a Proprietary RF protocol based on ESB (Enhanced Shockburst). Is there an IEEE or a different...
I am experimenting with trying to improve the current range of gzll nRF52840 dongle to dongle (which is not that far from what I need). I am developing using nRF5_SDK_15.2...
Hi,
The top level page nRF5 SDK Documentation Library page ( https://www.nordicsemi.com/DocLib/Content/SDK_Doc/nRF5_SDK/v15-2-0/index ) contains a link to "S140 SoftDevice...
