hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Is there any recommended way to flash the nRF51822-CEAA-R WLCSP chip?
Should a PCB design have UART design for flashing the nRF51822 chip after it is soldered on? Or should...
Hi, My problem is: When I programing my board using existing hex from SDK, I have no problem. Program working great. But if I building my own hex (build without errors) and...
Hello,
I am using nRF52832. My GPS is connected to GPIO pin (15, RX) and (16, TX) of nRF52832. My TCA9535 is connected to GPIO pin (8, SDA) and (7, SCL) of nRF52832. TCA9535...
Hi all,
I am currently building I2C communication between nrf52832 and a stm32 chip, stm32 as the master and nrf52 as the slave.
The situation is the stm32 couldn't get...
I am not connecting any uart lines to the device. But I feel the assert is being used as the timeout "handler" and then pressing button one resets the device.
I'm using...
Hi,
I'm currently going through this paper on the newest Bluetooth Mesh Standard ( http://www.mdpi.com/1424-8220/18/8/2409) . Although it's interesting to see that this...
Hi, we are using SoC nrf52810 SDKv14.2-SR3v1.2 for our RCU.
1.If there is a scenario the image transfer is finished, and the power lost happens when the old image is being...
Hello,
I am in the process of determining a system architecture for a sensor-bluetooth-android application. The goal is to read sensor information from an Android device...
I'm using Mesh SDK v2.2.0.
I want to create a new custom model,but I don't understand difference between Generic and simple onoff model.
Which model should I study?
I remember reading somewhere an article on how debugging with softdevice was going to be easier, with the debugger doing something along the lines of actually not stopping...
Hi dear nordic employee:
I use blew：
chip：nrf52832 CIAA-B00
SDK: 12.3.0
what‘s I want is same as this ， when the interrupt happen，I want to know the toggle is HIGH_TO_LOW...
Hi,
I want to develop a 4 Chanel Wireless audio system
I am using an EEPROM (without MC) to configure the nRF24.
I want to split the available band (2,4GHz to 2.5 GHz...
Hi,
I have the problem, that nrf_crypto_init() does not find any backends and thus is skipping the initialization.
What is the precondition for NRF_CRYPTO_BACKEND_SECTION_ITEM_COUNT...
Hello,
after migrating to SDK15 we noticed, that our spi master seems to clock out single bytes instead of a continous clock for the whole transfer.
The Migration guide...
