Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello,
I'm stuck in the nRF Connect SDK Fundamentals course on lesson 3, exercise 1. When opening the COM port to view the printk messages, I get an error when connecting...
We are seeing different behavior/performance on our system depending on whether we reset the system using JTAG (JLinkRTT Viewer) or we power cycle the system.
Our project...
Hi,
we would like to extend the measurement range of the PPK2 beyond 0.6 A in source meter mode, e.g. to measure the power usage of a Raspberry Pi. We know that this might...
I need a checksum to verify integrity of some data blocsk. As I saw, that the nrf5340 hardware has some builtin support for SHA-256, I though: cool, let's use SHA-256
Now...
Hi,
I build a custom board (nRF52840) but I'm not able to flash it using nRF5340DK with J-Flash via SWD interface.
1. The first thing I did was to do a full chip erase...
Hi,
Is it possible to communicate with the nrf52840 dongle from an android application via USB port ?
That is, nrf52840 dongle will be inserted to the android phone's...
Take Bluetooth UART as an example, there will be a delay in the process of sending data from the peripheral device to the central device to receive the data.
What factors...
Hi, I'm developing for a custom project board which only has the SWD pins exposed, which I'm using for (1) programming and (2) RTT logging during development.
Once the device...
I'm working on adapting ST's RFAL NFC library for ST25R3916B/X-NUCLEO-NFC08A1 on an nRF5340/DK in order to emulate an NFC tag, and would appreciate some insight into how Zephyr...
Hi, I use NCS v2.6.1 I have taken Central and peripheral HR as an example and am trying to modify it to make the Central/Peripheral UART example work similarly.
I briefly...
Hello,
I'd like to add the transmission of an I2C recovery pulse (where you toggle SCK 10 times) to my startup routine for an offboard device whose state I'm uncertain of...
Hello Nordic team,
I was wondering if it's possible to start the MCU boot from the application at runtime.
What I want is to be able to restart my product and run...
Exercise 2 doesn't seem to work for SDK v2.6.1 with v2.6.1 toolchain. SDK v2.5.1 works though. What configuration or code changes do I need to make it work for v2.6.1?
Hello,
I was curious if there was a project that uses 2 Mbps BLE to connect two nrf52840s, preferably with the ability to change which BLE channels the devices use. I...