Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
I have to use 240 bytes for my sensor value to send in bluetooth. so i choosed to work on ble_app_att_mtu_throughput i need only pheripheral to work on it . i have to remove...
Hi, I was wondering if hosting more than one nrf Connect for desktop version on the same computer was possible. The reason is that I need to use both the old app LTE link...
Hello,
I have connected a LSM6DSO sensor to my nRF52805 which is powered via GPIO. At startup zephyr RTOS wants to init the sensor and failed. After a reboot it detects...
On the SDK 17.0 NRF52840 platform, using sd_temp_get to read the chip temperature works correctly. However, if the sd_clock_hfclk_request function is used in subsequent operations...
Hello,
I'm trying out the example code "pin_change_int_pca10056". But the delay time between sensing a voltage change and toggling the output GPIO is quite long. 22us. Is...
I wanted to know in what ways can I connect thingy:53 to nrf9160 dk via Bluetooth? I understand that dk has onboard nrf52 and hence thingy:52 could get connected wirelessly...
Hi all, I am using the nRF52840 and I came across the nrf52_handle_approtect() func in modules/hal/noridc/nrfx/mdk/system_nrf52.c.
In the nrf52_configuration_249() function...
Hi,
I am unable to access P0.09 and P0.10. I face a similar problem to this thread . I've declared CONFIG_NFCT_PINS_AS_GPIOS=y in prj.conf. Also I've checked 0x1000120C...
i have a custom board that uses a nrf5340 that has been hardware modified so i can work again on getting my board to draw the mimimum power from the battery.
i have a PPK2...
I am using nRF5 SDK (17.1.0).
The MTU size is set to 53. I am using sd_ble_gatts_hvx() to send 16 bytes of data via Notification.
When I check the received data with the...
Hi,
Our product is currently undergoing FCC and ISED certification with Dekra. They are asking for 58741REM.001, 59675REM.001 and 64610REM.003A1 reports for reference. Can...
Hello! I am a newcomer to nrf and embedded programming (other than basic arduino and micropython projects). So far I have gone through many of the devacademy walkthroughs...
Hi, I'm trying to read data from an LIS2DH accelerometer using the nRF5340 DK board. I have been able to build and flash my code to the board, but the terminal outputs, "Device...
