I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
I’m using nRF Connect SDK v2.8.0 and working on BLE OTA (DFU) for the nRF7002 DK . I followed the Nordic “DFU with external flash” exercise and integrated it into the Wi-Fi...
Hi,
I'm in the process of porting our existing nrf5 project to nrfConnect SDK bare metal and am struggling to port our QSPI display driver. Are there any plans to add support...
Hello team,
I am working on a Direction Finding (AoA) setup using nRF5340 DK as a CTE Transmitter (Tag) and a Silicon Labs BRD4185A (AoA board) as the Anchor/Receiver. ...
We have developed device that used 2.6 and when moving to 2.9 everything broke apart and I cant get it to boot and I cant get any output from device. Be it from USB or SWD...
I am having a persistent issue with the ANT+ examples in the nRF5 SDK on an nRF52832 DK PCA10040. The application firmware compiles and runs correctly, but the ANT+ signal...
Dear Matter Support Team,
I have a setup where an On/Off Switch device is successfully bound to a Light device in our Matter network.
I would like to know which specific...
I am using the Ublox NORA-B206 module and facing issues with the debug option in the VS Code extension. The debugger fails to start, and I receive the following error message...
Hi Team,
We have a custom board with nRF9151 SoC that shows complete RF failure. The modem initializes correctly and detects the SIM card, but cannot detect any RF signal...
I'm adjusting my program with nrf52832 and nrf5SDK.
I attempted to use the parameter PM_PEER_ID_N_AVAILABLE_IDS to control the upper limit of the bound users.
However...
Hello, I am testing the power consumption of the npm1304 for the first time. To do this, I am using the PPK2 connected to the nPM1304-EK on VBAT and GND of the P1 connector...
Hello, According to the nRF7000 specification, the sleep current should be around 15 µA. Electrical specification .
We have a custom PCB with nRF9160 + nRF7000, and the...
Hello DevZone,
I'm testing the Matter OTA by using OTA provider. Referring to: Performing Device Firmware Upgrade in the nRF Connect examples
But it's too slow. Is that...
I want to update 52840DK FW using Matter OTA, but I have not found SOP, could you tell me how to operate?
BTW, I use Raspberry Pi4 connected with RCP as border router. ...
After flashing the official example hci_uar onto the nRF5415-DK, I proceeded to use "udo strace -o btattach.log btattach -B /dev/ttyACM1 -S 1000000 -R“ to bind it as an HCI...
Hello, I’m working with the nRF9151 and testing DECT NR+ functionality. I already have the binary image of the DECT NR+ PHY firmware and it works fine. I’m just curious—is...
