I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
Hi There.
I'm using the Asset Trackerv2 as a base for my application.
If I provision certificates at boot pior to enabling the LTE connection. the GNSS is never enabled...
Hi,
I'm trying to develop an application that uses an nrf52840-dk board and the pc-ble-driver-py. The dk is supposed to be a central device.
Using the python driver library...
1 I didn't understand ANT on nRF5340 under Highlights. I didn't find the introduction I thought of in the following article.
2 Added the CONFIG_ESB_DYNAMIC_INTERRUPTS Kconfig...
Hi all,
I have recently moved to the last nRF Connect SDK version. As of now, I am using VSCode as IDE. Unfortunatly I can not find a way to specify the flash runner when...
hi dev
I have a question about energy harvest over BLE beacon.
As you can see from previous tickets, I'm working on making beacons using energy harvesting.
And now I...
Hi,
I needed assistance to get the SKY66403-11 FEM working with the Radio Test Example in VS Code, for certification testing (FCC, CE etc). I am using the NCS 2.2.0 SDK...
Dear Team,
We are registering with https://imports.gov.in/MEITY/public/home for nrf7002 modules which were sent by Nordic team through DHL.
Please send us the IC code...
Hello,
I am currently working on nrf52832 and trying to change the sampling frequency to 10KHz ,ie, 100us and keeping buffer samples as 1.
Previously in the example we...
In the product specification of nPM1100, for fixed 500mA charging limit, ISET should be connected to VSYS. In the USB-configuration (Configuration 3) ISET is connected to...
Hi:
We want to test the nrf7002 WIFI performance based on the nrf7002 PDK.Do we have relevant test firmware?
We noticed that the sdk document of V2.1.2 has a description...
hi.
I have a firmware using standard GATT, now im implementing the mesh layer.
Im using SDK 17.0.2 + MESH 5.0.0. (im not using the new sdk connect because it is very difficult...
I'm moving from NRF9160DK to a custom board, where it has no UART. I plan to just use RTT for debugging messages.
However, I found if I delete the section which defines...
Hi,
I build secure_bootloader_ble_s132_pca10040_debug example (SDK17.1) on SES 6.30.
The only modification to the project is excluding SEGGER_RTT_Syscalls_SES.c.
...
It is possible to addressing nodes using MAC address of the device in Thread network?
In topology: PC <-> Border router <-> Thread mesh nodes
which IPv6 (Mesh-Local EID...
Hello
I'm new to the nrf platform and wanted to try out the I2C functionality of my nrf5340 DK. The only example I could find was the Fujitsu MB85RC256V FRAM I2C example...
