Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hi, I'm current evaluating the NPM1300. I've made a prototype board, using nrf54l15 and npm1300. I did not know that i need the npm1300 EK to do battery profile. Due to being...
Hi Team,
Currently I am working with nRF54LM20 DK. And tried to import and use echo bot example from SDK. And modified the overlay file as per the UART pin changes required...
Hello Nordic Team,
I am currently working with the nRF52832 on a custom board using nRF Connect SDK v2.9.0. I am implementing OTA DFU using Sysbuild and MCUboot with an...
I've just spent about 4 hours trying to figure out why a particular build was failing (on nrf9151dk).
Examing the cryptic errors finally revealed that the TFM partition...
Hello,
We have a custom board we are developing on that uses the nRF54L15 MCU. The board has some LEDs that we were hoping to drive using PWM, but these are connected to...
Hello! I have a Nordic Power Profiler Kit 2 that I am using to make measurements on a project. The issue I am having is I get an error message when trying to connect the kit...
Hi folks, so I will start by saying I have had this device working at home under Windows 11. I have brought the device to work to use on my works computer, which is still...
Hello Nordic Support Team,
I am experiencing a startup issue with the nPM1300 PMIC. Below is the summary of my hardware configuration and the behavior I am observing:
...
Hello Nordic Team,
I am working on an nRF52833 project using nRF5 SDK 17.1.0 with Secure DFU Bootloader.
Environment:
MCU: nRF52833
SDK: nRF5 SDK 17.1.0
SoftDevice...
Hi,
I am facing an issue with the latest nrfcloud-utils provisioning flow when using a custom nRF91-based board connected through a generic FT232R USB-to-TTL adapter.
...
Hi everyone,
I am trying to use SPIM for an external DAC. The DAC does not require MISO, only SCK, MOSI, and CS.
I configured SPIM like this:
#define SPI_DAC NRF_SPIM2...
Hi,
just got my PPK2 and noticed some strange behavior:
the only thing connected is USB data/power, no DUT. Power output is off. If you start logging it displays some...
Hi,
How to implement two sets of SPI on the NCS v3.0.0 nRF54L15 P2 port? If it can be achieved, please provide the corresponding IO ports for these two sets of SPI.
Kind...
Hi，
We are designing a cellular antenna based on the Thingy91x reference, which needs to support all frequency bands of the nRF9151 cellular module. The antenna tuning switch...
Hi Nordic team,
I am using nRF54LM20DK with NCS v3.3.0 and trying to enable QSPI.
However, there is no &qspi or &qspi20 node in DTS, and adding it causes build errors...
