[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
Hi,
I have an nrf9160dk which is not modified in any way as far as I can tell. I am not sure exactly which hardware revision (it just says 1.0.0 on the label), but it...
I'm trying to use the LVGL module inside zephyr, however, it requires specifying the zephyr,display driver in the device tree.
The zephyr sdk contains drivers for the FT81xx...
I am doing mcuboot using stm nucleo board through nrf connect . i am using blinky application for build but i got some error .please tell as early as possible
Building...
Hi, I am using the ZBOSS NCP production ready firmware from NCS v2.0 and I have some issue with serial communication.
I am able to run my application, and I don't have any...
HI ,
I am using west tool to build and flash the example . as I have tried this example (Nordic\v1.9.1\bootloader\mcuboot\samples\zephyr\hello world) , which is not working...
The version of bootload I use is as follows:
，Finally, the file was synthesized by NRFUtil and downloaded to 52840. The system started well when it was powered on, which...
Hello all, We 're working on our custom PCB prototype. We can see current consumption according to this profile even though the flash memory was erased. Also the modem FW...
Hello all,
I have started to port the code from the nRF52dk in Segger EM, indeed, everything so far works on the NRF52 dk , so I have opened the Blinky example for the nRF52820...
Hi,
I am using an nrf52 DK and facing an issue regarding the GPIO voltage levels. The GPIO voltage is around ~2.35V when its in LOW state and slightly increases when in...
Hi,
like mentioned in the caption, i have updated the nRF Connect SDK version from 2.0.0 to 2.0.2 and noticed, that the debugging does not longer work as expected and before...
Hello, I plugged in the nRF52840 dk and LED1 fades in and out. It does not blink. I am unable to connect to my phone. I tried to drag and drop some hex files to the JLINK...
Using the Power Profiler Kit II with
nRF Connect for Desktop (v 3.11.1) on Ubuntu 20.04 with the Power Profiler App v3.4.3
I'm wondering about the value of the time axis...
When operating in high-voltage mode, the spec says that VREGH,DROP is at most 0.3V . What happens if VDDH falls below the programmed VDD output plus VREGH,DROP, for both the...
Dear Community, Following the Nordic's sample of the (<ncs root>/nrf/sample/caf) the LED module & (CAF) Button module demonstrate the LED states & LED effects (awesome!) After...
Hello DevZone,
I'm using nRF5 SDK for Thread and Zigbee v4.2.0 and trying to test Zigbee OTA example and faced some troubles.
I'm following this guide https://infocenter...
