pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
In our application, we've enabled full modem firmware update, which requires us to enable CONFIG_NORDIC_SECURITY_BACKEND. When we also enable memfault, this compile time pre...
I am build an application with features : When I not used nRF it imediately in sleep mode and be wake up by BLE events to send some text, and return to sleep mode ( the reson...
Hello there, Thanks for writing an application layer for SGTL5000. https://github.com/NordicPlayground/nRF52-teensy-sgtl5000-audio
I've configured the SGTL5000 to source...
We have a simple coin battery powered BLE device with a Laird BL652 module which has an nRF52832 chipset.
We have three buttons and set it up as low power as possible...
Hi, I downloaded a project from Git. I tried to open in SES using nRF Connect SDK. During the initial Cmake, the error occurs as shown in attached image.
Hello,
Our aim is to install "pc-ble-driver-js" and use the connectivity board for the serialization process.
We are following this link to get this working https://github...
Hi!
In previous versions of the SLM it was possible to provide a hex datatype to the XUDPSEND command to send blobs of data over UDP, without having to worry about a stray...
Hi,
I enable the watchdog in the application image, then call soft reset to enter the bootloader, the bootloader execution is also normal, until the watchdog is reset. ...
Hello!
I have a situation where a chip is connected with an antenna on a u.FL slot, what I want to do is to remove that antenna from the chip and connect my nrf52840 to...
Hi,
I want to send the I2S MIC Raw data through Ble by using ble_nus_send. I have written one application but it triggers a Cmake error. I have attached the log below...
HI I'm using the nrf5340dk, and I'm able to flash the application core with code that toggles the LEDs.
But I'm not able to flash the network core. I've specified in the...
Hi, I'm currently designing a system which requires Heart Rate monitorization and I'm using the MAX30101 chip to do so. I will be using I2C communication and, therefore, based...
1. We use code similar to the existing sample code to repeatedly sample a 0 - 2.25V voltage range using the SAADC. 2. Settings: 30s interval, single-ended input, burst-mode...
Hi All,
I'm looking for a PC based tool with similar functions as nRF connect. Our manufacturer is developing a functional test fixture which will PC based and will be...
Hello,
I'm looking for reading the sent data from an old embedded autonomous nRF905 (which act like an active tag) and I thought I could use this convenient-looking USB...
