I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Hello,
I currently have a product using the nrf9160, that started development 4 or 5 years ago. The firmware uses SDK 1.6.1, and whilst I have had to correct some bugs...
It's now two years ago, and the ticket had a different scope. But one of the answers from Nordic there was:
"This is because the spec mandates that if the device gets rejected...
I have installed the NRF Connect app on my Windows 10 PC, using "Run as Administrator" and keep getting the following error message whenever I try to install any of the products...
This is also my Bluetooth Prj.conf
When I turn on 2.4G, there will be an error message. How can I solve it? BLE and 2.4G cannot coexist at the same time. Can I switch...
I'm using the NRF5340. When I open a standard example project located in the directory: nrf\samples\bluetooth\peripheral_uart (the well-known Bluetooth data transparent transmission...
I'm using the NRF5340. When I open a standard example project located in the directory: nrf\samples\bluetooth\peripheral_uart (the well-known Bluetooth data transparent transmission...
Hello Devzone,
How can the nRF5340 App core read the "version number" of the image flashed to the Network Core, e.g. the FW_INFO fields, or something similar?
I am using...
Hi,
Is there an API, data structure or else in nCS v2.9.0, monitoring of which i can understand if ble advertisement is active or not active or at fault.? Also, if at...
Hi, I am using sdk 2.3.0. I got the following warnings while building the project. The build finished without any error, but it didn't perform as expected. Should I concern...
I am building a project based on the aws_iot example. I am using sdk 2.3.0. I can connect with either lte-m or nb-iot, but I keep getting aws_iot_connect, error: -119. What...
Hello, I am working on a custom board with my own custom project. I want to perform DFU for all the images I mentioned. The mechanism for the OTA update will be as follows...
I am unable to read PDM microphone on my custom board or nrf54l15-dk.
My environment:
- nRF Connect SDK v3.0.2
- nrf54l15-dk
- custom board with Fanstel BM15C -...
Hello,
Revival of an old nrf52840dk board I would like to use for another project, I'm trying to flash a sample application to it but it always fails with the following...
The NDEF message is slightly different between Type 2 and Type 4. Type 4 has a 2 byte length field at the very beginning of the file, called NLEN. The NFC Type 4 example code...
Hi.
I made a board with nRF54L15. I would like to use P0.01 on nRF54L15 as GPIO output., but I failed to confirm P0.01 turn high.
Then, I asked nordic AI anything to solve...
