Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Hi there, I'm trying to combine the BLE Multilink example with the Throughput example, with the hope that I can connect 1 Central to 2 Peripherals and get a high throughput...
I would like to emulate a NFC type 2 tag on a Nordic nrf52833 based device. I have the source code for the NFC driver (nrfx_nfct.c), but I can not find the source code for...
I would like to know if Nordic could provide me with a Zephyr compatible pre-compiled nfc_t2t library (nfc_t2t_lib_gcc.a or nfc_t2t_gcc_no_fpu.a). I managed to link library...
With SDK15.3 (it appears the issue exists in 17.1 as well), we are using the flash backend. To read the logs, we are doing the equivalent of flashlog_read_cmd(). This eventually...
Hi Everyone,
I recently purchased an nRF52840 DK (PCA10056, 2.0.1, 2021.7, 68365177) from mouser. Yesterday I successfully installed the nRF Connect for Desktop v3.9 application...
Hi there,
Does Nordic provide support directly for the Taiyo Yuden EKSKDNZWB Eval Kit and the EYSKDNZWB module? The Taiyo Yuden documentation seems to suggest that's the...
Hello,
I'm trying to see serial data (polling async method) coming from a single-wire signal. I have verified via an oscilloscope that there is indeed data on that wire...
Hello,
We are using nRFSDK v15.0.0 and nRF52840 in our system. There is also an external MCU that is connected to the nRF52840 via UART. Currently we are trying to perform...
Dear Members,
I want to use SDcard with softdevice, when I run fatfs_example()
I got this :
nfo> app: Initializing disk 0 (SDC)... rror> hardfault: HARD FAULT at...
Hello,
I've been working on a simple application to scan for bluetooth packets being emitted by another system, which advertises at a consistent 10Hz. We apply a filter...
Hi,
I try to do a OTA Update with watchdog enabled . The OTA Update runs and boots image B but this is stopped after watchdog timeout (1Sek). In my code the watchdog runs...
Hello all,
I am trying to develop an application where the user will input some specific commands i.e hex value of 0x01 via a mobile application and then via bluetooth this...
Hi,
I am migrating my code from sDK15 to SDK17. In SDK15 code app_timer_start() working fine with any timer value. But in SDK 17, I am getting error code 7.
When I debug...
Hai
I'm working on nrf52832 NFC, I have a few questions.
is NFC ID in nrf52832 is unique?
can I use it for payment purposes?
if that ID is not unique, any other solution...
