I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Hey Devzone
Running into an interesting issue with the .zip files on http://developer.nordicsemi.com/.pc-tools/toolchain/ . When I try to download in browser they fail....
Hi
I am using nrf51422 (on the DK) with S130, SDK12, functioning as a central, reading multiple peripherals (which I also programmed),
Some of those peripherals have manufacturer...
Hello, With reference to Case ID: 278209, I wanted to include a driver file, for which I was suggested to add the label/variable "zephyr_library_include_directories(.)" in...
Hi,
I have a strange problem.
When I connect the jlink and battery power on board at the same time,and download the application, it works normally. But when I disconnect...
Good morning.
I have a custom board with softdevice 132 and sdk 15.0.3 where I have configured pin P0.16 and P0.17 for uart (rx, tx). I have read in other posts/problems...
I have written BTLE code that works on the nRF52840 DK using SoftDevice s140. I have ported this code to work on the nRF51 DK and nrf51822 MCU using SoftDevice s130. I use...
Hi all:
on my project,i set
define NRF_SDH_BLE_PERIPHERAL_LINK_COUNT 1
define NRF_SDH_BLE_CENTRAL_LINK_COUNT 6
on my peripheral , i need mtu = 185
on my central...
The application of a device is developed based on ncs1.3.0, now the SDK version is upgraded, the firmware function is developed based on ncs1.5.1, and a problem is found,...
Hello,
I'm in an aging manufacturing space and would like to utilize your sensors, but im concerned the pillars and walls will prevent data from being sent. I read the...
Hello,
I am using Nrf5340 with “Direct test mode” example.
I try to make my nrf5340 kits to be an AoD receiver under the DTM.
Now,I am able to run the example code to...
Hi,
I'm using spim on nRF52810.After I init the spi driver and using APP_ERROR_CHECK(nrf_drv_spi_transfer(&spi, &Command, 1, m_rx_buf, 1)) , RTT Viewer showing FATAL ERROR...
Hi,
Is there a way to control the 1Mhz BLE symbol clock?
We want to use nrf52840 as a GFSK transceiver and we need to control the symbol clock (up to +- Khz resolution...
Hi,
I'm running into issues where iOS is caching the handles. I found out that I need to set IS_SRVC_CHANGED_CHARACT_PRESENT to 1.
But where should I do that? In sdk_config...
Currently messing with the NRF52840 chip and given examples (NRF Connect SDK v1.7.0) on two different eval boards (the nRF52840-DK from Nordic and the BMD 340 Eval board from...
