Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
When I do a 'build and run' in Segger Embedded Studio I get this error
Then I press the reset button and everything works.
If I do 'build and run' again the error repeats...
Hi
I would like to add to the scan_adv example, the possibility of the FOTA upgrade.
I can merge the scan_adv and smp_svr examples, and get them to work at the same time...
Excuse me:
1、The customer wants to use p0.21 pin as General purpose I/O，Can the reset circuit of p0.21 pin be removed？
2、The customer said that when a new nrf52832 chip...
Hi,
I want to add DFU over mesh and usbd into the client example.
I have faced an error of Multiple definitions of UARTE0_UART0_IRQHandler. I comment out the UARTE0_UART0_IRQHandler...
Hello,
i am currently trying to create a project that uses the NRF52840 board as a switch to control sylvania smart+ A19 filament light bulb.
However, i am unable to detect...
Hi,
I'm using NRF52840 in order to implement an application which will connect to a mobile device with PIN code (MITM). In addition - my app will be able to connect to a...
Hi everyone,
I'm using the nRF5340 board, nRF Connect SDK v1.5.0 and the nRF Connect app.
I am also using the example code "beacon" and all the data with integer format...
Hello,
I have been developing a serial C# application to work with the nrf52840 chip, initial development was done using the nrf52840 development kit which worked without...
Good morning,
I am using SDK 16.0.0 and nRF52832 uC. I have a project where I need to connect the uC to a CoAP IP. The only internet access it has is through an SoC developed...
Hi, Usually we set FLASH_START macro to indicate application start address, I do like to consult is't possible to change the FLASH_START from prebuild binary file without...
Excuse me:
PCA10095 cannot be download .hex on SES and nrf conncet programer,The figure below shows the problem downloaded on SES.How to solve tihis problem？
Hi, dear Nordic & all：
When I run libuarte example，I found a problem， I just set P0.14 to high at the begin of mian function, then I send data and test the example's function...
Hello,
I'm trying to develop an application sending GPS over HTTP requests.
I started from the "https client" and "agps" samples in the NRF Connect SDK: the single examples...
Hi,
I'm trying to build secure bootloader DFU(non_debug_version) for PCA10040 with the below mentioned prerequisites and I'm able to build the bootloader successfully...
