Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Although my Googling skills are not the best I have, so far, been unable to find any examples or driver documentation for the comparator peripheral of the nRF52840 for the...
I'm using the asset_tracker app on a custom board and have built 50 of the custom boards. All but one of them start the modem and listen to the LTE receiver for a full minute...
Hello, I followed getting starting guide, and got SDK and tools installed for nRF52-DK, I'm trying to open, build and run some examples. But when trying to open any example...
Hi.
I am using nRF52840 dongle and running saadc example on it.
To print the ADC data buffer "p_event->data.done.p_buffer" in PC, I am using USB_CDC. The size of SAMPLES_IN_BUFFER...
I have implemented the custom service and added custom characteristics following the tutorial series, now I can connect and see the characteristics and their values. I can...
My NRF52DK (PCA10040) J-Link always shows SWD speed 1000 kHz, even if I set the speed to 2000 or 4000 kHz. Is it not possible to connect at higher speeds?
I was working with "Debug configuration" for my nrf board on Segger Embedded Studio. It was working perfectly. But when I changed it to "Release configuration", It doesn't...
Hi everyone,
I am using nrf52840 and I want to change the advertising name in bootloader from "DFUTarg" to a custom name on application side.
For unbonded one, I saw...
Hi,
I'm using the provisioning example from the mesh sdk and I have an "ASSERTION FAILED at :0" error when I'm trying to re provision a node that I have provision before...
Hi
I try to understand where does the interrupt proirity for UART is set.
I see that uarte_1_init() is called from uart_nrfx_uarte.c.
uarte_1_init() is declared from...
Hello I am using sdk v17.0.2.
I found a problem with Bluetooth connection while using 'ble_nus_data_send()'.
the system will stop if disconnect the Bluetooth while transferring...
Hello
I'm asking a question because there's a part that doesn't work well while using ble_nus_data_send().
There is a problem sending continuous data to the app using...
Hello
Sorry this is a basic question and I shouldn't be bothering you with this but I have already dealt with a number of issues with Segger so I couldn't resist. - I have...
Hi, I open ssl socket to the server (without certificate verification), and then use an http_client_req() call, to perform the actual http request (with additional optional...
