Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
Hello All,
I am trying to find out examples codes for enabling the external 32kHz crystal for nRF52832 design.
Can someone help me here?
I am using SDK Version 16...
I am using the nfc library (nfc_t4t_lib) on the NRF52832 chip with SDK 17.0.2. When I approach the NFC antenna with a nfc reader (like a smartphone) and leave the reader on...
Hi everybody. I'm trying to design a mesh network in which most of the nodes, if not every, should be a relay due to parallel positioning of the devices and each one of them...
I am working on Windows, using NRF Connect SDK 1.5.0 (have also tried the SDK 1.5.0r-rc1, with an updated nrf_802154_serialization module to be able to compile).
I am using...
Hello, I have run into this problem again with regards to using the lwm2m_client sample. I can start running it fine but I get the error "Cannot init lwm2m engine" and "Cannot...
when compiling "ble_app_multirole_lesc_s140_pca10056" of sdk nRF5_SDK_17.0.2, crypto library not getting included, I am getting error, library is placed as shown in pic, also...
Hello,
I know that you can generate a single zip that contains dat and bin files for sd+bl and dat and bin files for the app.
Is it possible to generate a single dat and...
HI, I'm new here, hope following the rules for Questions.
I'm using nRF Connect v.3.6.1 and as toolchain SEGGER Embedded Studio for ARM (Segger edition) V5.34a.
I need...
Hello there,
I am using nRF52840 PDK and nRF5_SDK_for_Thread_and_Zigbee_v1.0.0 SDK for BLE and Thread development. I also have a BLE smartphone app communicating with nRF52840...
Hi,
-I have a custom board using nrf 52832 and I have interfaced LIS2DH12 using an SPI interface. -I am using SDK 15.2.0. -I am collecting raw data using FIFO mode and send...
I want to realize audio playing function in 9160, according to the specification, there are 9160 I2S interface. However, the specification only describe the definition of...
I am testing UART example using nrf52 DK(nrf52832), SDK17.0.2. (\examples\ble_peripheral\ble_app_uart\pca10040\s132) Setting UART initialization to a specific pin will halt...
I use ANCS example from SDK 15. But I found that I'm not able to get more than 32 chars for ATTRIBUTES (BLE_ANCS_ATTR_DATA_MAX). And it's a little short to get Title, Sub...
Hello,
in our application we have one central (nRF52840DK) and up to four peripherals (nRF52832). We want to achieve two goals in this application:
Goal 1: We need a synchronized...
