Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
I'm trying to evaluate the nrf5340 and flash a basic blinky application but I get an nrfjprog error when I run `west flash`:
[0/1] cd /Users/user/zephyrproje...Cellar...
I want to move the uart communication port from default pins to
#define RX_PIN_NUMBER 33 #define TX_PIN_NUMBER 34 #define CTS_PIN_NUMBER 35 #define RTS_PIN_NUMBER 36
I...
Hi There,
How to control led using pwm during dfu mode (when dfu programming is on going).
HW:PCA10056
SW: nRF5_SDK_15.2.0_9412b96
Example: ble_app_buttonless_dfu
I really did not want to ask, howeverI have spent a lot of time on this and still no joy.
I have a epaper shield have got the electronic paper display working. so SPI writes...
Hello,
I see on you webpage that there is an evaluation kit for nrf21540 -> PCA10112 . do you have the schematic of this board ?
For the moment I'm using the NRF52840...
Hi Guys,
We have a need to send data every 4 hours.
In order to do this, we sleep 1 hour at a time (1-hour timer - single shot) and increment counter, and when the count...
I'm using 2 nRF5340PDK with nRF Connect SDK 1.4.0. 1 PDK with central_uart and 1 PDK with peripheral_uart.
When I change the clock config of the peripheral_uart by using...
using nrf-9160dk and iBasis SIM with pre-built asset tracker app (2020-10-30_5522ca2b) and nrfCloud
First time the device was registered data transmission worked.
Now...
The design has 2 sensors on SPI with mode 3 and the nrf21540 which is mode 0. Can you have 2 different Modes on the same spi bus?
would i use the SPI transaction manager...
Hi,
I have the barest of PCBs with literally just the nRF9160, SIM slot and antenna, and have wired it directly to an Otii Arc, so there is no power circuitry either as...
Hi All,
If I want a Thread device to automatically start commissioning when it starts, is there a code example in Nordic SDK?
Now I just found the API interface, called...
NRF52832 is using the protocol stack and updated by OTA. Why should the number of FDS Pages of the new firmware be equal to the number of FDS Pages of the old firmware?
Hi,
I am using NRF52810 , In my project I need to store Float value and uint32_t value in EEPROM / Flash for permanent storage (Non-volatile storage).
With SDK17 i am...
Installing a toolchain for nRF 9160 is not easy as installing the Arduino IDE ( at the leat in Ubuntu). I request Nordic Semi to install all the required tools in a cloud...
