In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Hi everyone,
I'm using SDK 15.0.0 S132v6.0 and looking for a way to get an event when the advertising times out. I discovered the softdevice_ble_evt_handler_set() in this...
Hi,
I am developing a device based on the PCA10059 board, SDK v15.3.0, and softdevice v6.1.1, and I want to imply that I am using the FDS module with 20 pages in my firmware...
Even after I get a license for the Nordic stuff, SES won't show an installed activation:
The license "installs" fine though:
And I do have the "Nordic" version...
Hello,
When I try and use nRF connect Programmer to update the modem firmware via USB it fails each time in the second step (Modem Firmware Update) with the error message...
Hello Nordic,
I'm working with NRF52840 (with SDK 16 and softdevice s140 7.0.1) in my project, which acts as a central, and an IOS phone as a peripheral. I have a read/write...
I have an nrf52833 wired up to 25 switches and detect changes via the pin SENSE configuration triggering the GPIOTE PORT interrupt. My interrupt handler: 1. reads the pin...
Due to whitelist limitation of 8 peers, I am doing manual filtering of bonded devices. I am trying to use pm_address_resolve function to figure out whether I have previously...
I am using nrf52840 DK and communicate with Raspberry Pi 3 through UART port. The Raspberry Pi is used as a gateway. The baud rate is set at 115200 default on both nrf52840...
Hi, I am trying to integrate ADC in my project( ble_app_template ) but getting garbage data. I have nothing connected with pin P0.4(NRF_SAADC_INPUT_AIN1) . (Means not applied...
I am budding Embedded Engineer, currently, I would like to learn how to program nrf52dk. While I am exploring info center, Peripheral examples I have noticed that most of...
Hi,
I have successfully created the bsd_os port for BSD lib. Everything runs without crashing. However bsd_init always returns 3, no mater what. Which in turn causes the...
Hi,
I am using nRF52832 on a PCB that is designed by me. I tried to toggle one LED on my board, it is connected to the P10 of nRF52832. I changed the LED number in pca10040...
I try to use GPS and LTE together in the nRF9160DK.
To do so I turn LTE on, connect to MQTT broker and send a message which got PUBACK handled in mqttEventHandler().
Then...
I originally posted this question in the community forum , but I think now that it fits here better. I won't repeat everything since you can see the details in the community...
I am using the PCA10056 development board, running a custom application merging the MESH stack (2.0.1) with an IAR-based SDK v15 template, sd 140 v6. Whenever I go to debug...
