pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
I'm trying to use the QSPI periph to interface to a Flash, the project is based on the blinky and has UART and SAADC added in so far. I can use nrfx_qspi_cinstr_xfer to read...
Hello,
I am developing an application for location tracking to be run on a Windows computer. The computer will be communicating to a mesh network using the serial interface...
Hi,
I'm using nRF52840, with NFC pairing (based on SDK examples).
The problem is that sometimes, after advertising, my device is waiting and nothing happens. After using...
nRF52832, SDK14.0.0, S132v5.0.1
http://infocenter.nordicsemi.com/pdf/nRF52832_PS_v1.4.pdf
Section 18.8 (page 83) shows that the WDT registers are retained across Soft...
Build and flash mqtt sample. Use board nRF9160. Ubuntu 16.04. Firstly flash secure boot, just after that flash mqtt sample. Have this in terminal:
The MQTT simple sample...
Hey everyone, I am trying to setup the external temp sensor instead of using the simulated data
I modified prj.conf to:
CONFIG_TEMP_USE_EXTERNAL=y
and Kconfig default...
Hello
I used the pc-ble-driver-py to advertise Apple ibeacons, but it seems that they're advertised as connectable undirected packets which is not good in my case, as...
Was told to avoid using nrf and particularly to mix nrf/nrfx functions.
Need clear sdk_config.h requirements to setup that also addresses what must not be in the config...
Hello to everyone.
I'm working with Light_switch example for nRF52832 (PCA10040) and Mesh 3.1. I'm trying to modify the server example and to do that I need to know where...
Starting from this example I try to bring clock functionality to my BLE-project.
1. The external LFCLK-XTAL
I need some clarification about the use of the different...
Hi Team,
May I know your kind advice on the following issue when I tried to Open the SDK project in SES. I have seen some discussions on line but none of them works for...
I'm trying to migrate from SDK12 to SDK15, but my code always crashes at advertising_init() and goes to NRF_BREAKPOINT_COND. Even when I directly use the example from the...
I tried searching for this response but cant find exact answer
SDK15.2 and API6.1
I am trying to have an advertiser but would like to put it in some sleep mode and advertise...
There are a few pins I want to use but are already assigned to MCU interface UART or buttons like p0.05 to p0.08 and p0.11 to p0.16 on the nRF52840 DK. I’m wondering if it...
Hi,
We are encountering a problem when we try to avail Nordic UART service (NUS) and Mesh service in one application. The problem statement is that after Provisioning, when...
