GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Still trying to get anything ta all to work on the nRF52-DK
I erased the chip
I flashed the soft device "soft_device_s132_v3.3.3" to address 0 and verified
built...
Hi!
We are having problems with pairing & bonding procedures with iOS devices.
On the peripheral side we are using a nrf51822 BLE module on which we are testing pairing...
Hi all,
2 days before we bought nrf52832 board.
in new board i can able to execute all peripheral example ( LED BLINK,button,uart,timer..)which doesnt need softdevice...
I'm trying to setup the RTC in the nRF52 to count with a resolution of 1mS. As the count has only a 24 bit value, I wish to clear the count every hour to start again.
There...
Hi all,
I'm having a error on my code, and wanted to understand it better. I'm using a custom board with a Rev.3 CTAA chip, 256k Flash and 16k Ram. I have BLE initialized...
I measured my Nrf51822 current:
when my VCC is 3.0v ~ 3.3v
my current is 0.16 mA.
when my VCC is 2.6v ~ 2.8v
my current is 1.5 mA (why?)
when my VCC is lower than 2...
I have issue with nrf51 booting, i noticed that sometimes when i plug the power to (VDD and GND) the system dosent turn on at al.
1 - how does the system the whole system...
amigos de habla hispana estoy comenzando con este circuito.
mi duda es cual compilador utilizo para crear un simple led blink..
tienen algun tutorial en que me puedan a...
Hi.
I am using the nRF52 Preview Dev. Kit to send data over multiple channels by
setting the NRF_RADIO->FREQUENCY register to the desired frequency value.
To make it work...
Hi,
I am trying to measure the temperature using sht21 sensor with nrf51822. I am using TWI to do this. When I try to send a data to the sensor the application cannot do...
Using the nRF52832 and SoftDevice s132.
If the application code disables the SoftDevice, then the application CAN erase UICR memory in the nRF52832 device.
The question...
I control a module over UART using app_uart_fifo. This module is controlled from nRF host by commands to perform things. This generally works fine but however, sometimes when...
Hi,
I write a code for the max6657 temperture via modifying the SPI MASTER Example. The function for reading max6675 via SPI is shown as follow
uint16_t readCelsius(void...
Dear Nordic Team,
Thanks for supporting.
How to calculate the battery voltage level from Eddystone TLM. Its always transmit 240mV.
I am using CR2302 3V battery.
...
