pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
Hello, I want to purchase cables to connect a Flasher Pro (cable should end on DB20 Female) to an nRF52-DK onto "Debug In" connector (cable should end on mini DB10 Female...
Hello, I am developing a solution based on nrf52-DK, using nRF52832.
I am trying to use JFlash to read Device Serial Number. I could read it with JLink , with command "mem32...
Hi, hope someone can help me.
The past 3-4 years I have used SDK 17.1.0 and SES for SW development where the SW is running on a nRF52840 SoC which is the heart of our product...
I'm working on a Docker image that includes a VS Code server for the purposes of workshops and training, and I'd like to install the nRF extensions (e.g. https://marketplace...
hi，bro
I want to support both BLE and GZLL simultaneously and perform the corresponding initialization work based on the value of a variable, mode . However, when I set...
Hi,
I have difficulties to sniff BLE packets with nRF52840 and wireshark between a remote controller and phone.
I can capture all the pairing process, I see DHKey exchange...
Greetings!
I am looking into Bluetooth Mesh, and the allowed radiated power according to Norwegian law. The general limit for 2.4GHz is 10mW, but if we utilize FHSS the...
Hello, I'm running into an issue with the "modem shell for NR+" application on a pair of nrf9131ek evaluation kits. The local sales rep. suggested that I reach out to Nordic...
Hello, I have a pair of nRF9142EK devices that I've been using to test DECT NR+. Now, I'd like to test out one of the boards with the cellular modem firmware for nRF9131EK...
Hi Support team,
I am using nRF9160 module and i want run two server on the module, one is modbus server and other is CoAP server. so is it possible to run both server...
When using the adafruit feather nrf52840 , the lowest I can seem to get power usage is around 400uA (including with the boards/nordic/poweroff sample ) .
This is my device...
Hello
I'm exploring the mesh dfu transfer, get some strange results
Here is the setup
1 distributor, 1 target
On the distributor I start the transfer with mesh models...
Hi,
I need to setup shell interface on both sides to exchange sensor data via uart.
The connection is as follow: cable 1: nRF52840DK Pin (TX - P1.02) → nRF9160DK Pin...
