Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi,
as discussed in different issue on DevZone . We have discovered that send command freezes the program in the CoAP client sample. The Nordic employee Hakon has confirmed...
Hello,
This is related to a previous post , but now with new information and a more specific issue to resolve.
We have product in the field based on RF Digital's Simblee...
HI
I used nrf51822- EK board.
BLE HID MOUSE - SDK 8.0
`
How to send left button or right button data?
How to modify below method?
static void mouse_click_send...
Hi everyone,
I'm working on a custom bootloader for nrf52840-based board. The bootloader needs to support DFU from an external SPI Flash and also BLE. I was working on...
Hi everyone,
I am trying to use the nrfx_uarte driver. I did the following:
(a) setup driver
(b) setup the event handler
(c) finally tried to send some testing...
I noticed a lot of the early SDK's 11, 12, 13 examples that had the service changed characteristic enabled. I'm using SDK 16 and it seems that most examples don't enable the...
I'm building an LTE device that only needs the GPS, LTE, motion, and button.
I'm trying as the first step to disable all the sensors that are not needed so that I don't...
Hi Nordic When the BLE is connecting, the fs_event_handler hasn't any callback after doing nrf_fstorage_erase or nrf_fstorage_write.
It seems like the storage (nrf_fstorage_is_busy...
Hi,
I noticed that there were changes in some of the priorities in SDK config - these defines were changed from 7 to 6.
NRFX_CLOCK_CONFIG_IRQ_PRIORITY
NRFX_GPIOTE_CONFIG_IRQ_PRIORITY...
Hi Nordic Support,
I am currently developing an IoT application (battery powered, cellular device with a few sensors connected). I have spent the past year building the...
I've read a lot in different posts about this but still fails to wrap my head around this.
We have a device using GATT with a few services, each with a few characteristics...
I am investigating Bluetooth mesh examples, which you presented, and I faced with incomprehension with initialization of struct bt_mesh_elem . Can you explain the meaning...
Does Nordic have an examples for implementing symmetric encryption at the BLE application level? I'm trying to understand how best to start because the Bluetooth LE security...
I have a setup where nRF91 and nRF52 on nRF9160 DK have to exchange ASCII strings over UART. nRF91 runs Zephyr and nRF52 - nRF SDK for Mesh.
When nRF52 is unprovisioned...
We are using mesh SDK v3.2.0, nRF SDK 15.3, nRF52840 DK and SES as our IDE.
We had a mesh network with around 5 devices and after a while 2 of them just stopped sending...
