In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
I'm developing a sensor node using light_switch_serve as an endpoint to receive commands and send sensor's data to light_switch_client. The examples works perfect, but I would...
Hi,
I`m using MDBT50QRX (Raytac Nordic 3rd party for modules) I need to connect and program the firmware hex file (connectivity_4.1.1_usb_with_s140_6.1.1.hex) which is on...
Hi,
Intention:
I want to build and run a sample application without suggested IDE on my custom nRF52811 PCB.
Previous steps:
Based on a tutorial [1] I found I was...
Hi,
I successfully tested ecdh and aes256 in seperate projects but I want to combine them.
This is my code:
Problem is that when i call the ecc functions this happens...
Hi, I'm using nRF Mesh App to provision more than 5 devices for vendor specific models other than on/off model. My purpose is to send some data instead of on/off the light...
Hi all
I am using a nRF52840 with SDK 15.3.0 and s140_nrf52_6.1.1 soft device.
My application is a multi-peripheral device that has a common service, each peripheral can...
Hi
I'm really new to this, forgive me it's a stupid question. I'm using the nRF52 DK from Nordic.
I started with the "Developing with SEGGER Embedded Studio", but when...
In the user manual of nrf52832 it is said that ram[n].power are retained registers in sleep mode and that depending on the settings.
One or more RAM sections can be retained...
Dear Nordic DevZone Team, With ARM cortex M4, it is possible to go into deep sleep mode. In the Nordic nRF52832 which uses M4, it is configured for BLE advertising. I would...
Hi
I read nRF52840 - LPCOMP information on datasheet and SDK.
It shows VHYST value is 35mV (typ.) in datasheet page 191 and 50mV (typ.) in SDK - nrf_lpcomp.h.
which...
Hello,
In addition to previous ticket I have further queries. I have a stringent requirement for reduction of Current consumption.
https://devzone.nordicsemi.com/support...
Hi, I've got a quick question here about using the GPIOTE driver in tandem with the GPIO HAL . For simplicity's sake, I'm using an in-house library that gives me high-level...
I have been encountering a rather latent bug in a product that we are developing. It consists of a custom nRF52832 board, that is connected to an nRF52-DK via ESB, and the...
Hi
In eddystone when we connect the beacon in connectable mode then it start non connectable advertising automatically without disconnect, same time we can change parameter...
How to send some data from light_switch_server node to light_switch_client node in the mesh sdk examples of the new version mesh sdk 3.1.0?
I basically want to send data...
