Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
At the end of last year, the new package nRF5240 WLCSP was delivered and it is now available in the market, however, I have not found an official layout for this new package...
I'm trying to use the QSPI periph to interface to a Flash, the project is based on the blinky and has UART and SAADC added in so far. I can use nrfx_qspi_cinstr_xfer to read...
Hello,
I am developing an application for location tracking to be run on a Windows computer. The computer will be communicating to a mesh network using the serial interface...
Hi,
I'm using nRF52840, with NFC pairing (based on SDK examples).
The problem is that sometimes, after advertising, my device is waiting and nothing happens. After using...
nRF52832, SDK14.0.0, S132v5.0.1
http://infocenter.nordicsemi.com/pdf/nRF52832_PS_v1.4.pdf
Section 18.8 (page 83) shows that the WDT registers are retained across Soft...
Build and flash mqtt sample. Use board nRF9160. Ubuntu 16.04. Firstly flash secure boot, just after that flash mqtt sample. Have this in terminal:
The MQTT simple sample...
Hey everyone, I am trying to setup the external temp sensor instead of using the simulated data
I modified prj.conf to:
CONFIG_TEMP_USE_EXTERNAL=y
and Kconfig default...
Hello
I used the pc-ble-driver-py to advertise Apple ibeacons, but it seems that they're advertised as connectable undirected packets which is not good in my case, as...
Was told to avoid using nrf and particularly to mix nrf/nrfx functions.
Need clear sdk_config.h requirements to setup that also addresses what must not be in the config...
Hello to everyone.
I'm working with Light_switch example for nRF52832 (PCA10040) and Mesh 3.1. I'm trying to modify the server example and to do that I need to know where...
Starting from this example I try to bring clock functionality to my BLE-project.
1. The external LFCLK-XTAL
I need some clarification about the use of the different...
Hi Team,
May I know your kind advice on the following issue when I tried to Open the SDK project in SES. I have seen some discussions on line but none of them works for...
I'm trying to migrate from SDK12 to SDK15, but my code always crashes at advertising_init() and goes to NRF_BREAKPOINT_COND. Even when I directly use the example from the...
I tried searching for this response but cant find exact answer
SDK15.2 and API6.1
I am trying to have an advertiser but would like to put it in some sleep mode and advertise...
There are a few pins I want to use but are already assigned to MCU interface UART or buttons like p0.05 to p0.08 and p0.11 to p0.16 on the nRF52840 DK. I’m wondering if it...
