I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Hello!
I fill in a dis struct with the fields manufact_name_str, fw_rev_str and sw_rev_str. Everything is dandy and works perfect.
Then I also fill in the field serial_num_str...
In product spec for nrf52832:
Neg30dBm 0xD8 -40 dBm Deprecated
Neg40dBm 0xD8 -40 dBm
Similar stuff in the SVD out of SDK 12.3
When I convert the svd to rust (using...
Hi,
I am using NRF51822 and sdk12.2. I am using Softdevice s130 with peripheral experiment_ble_blinky example. I have merge UART example in this and it is working fine. ...
Hello,
We've stumbled upon a weird behavior on iOS making the smartphone unable to reconnect to our wireless device after a DFU from SDK11 to SDK13 (nRF52832): the notification...
Hi!
I am getting a HardFault when I try to read a GATTs value inside a GPIOTE ISR handler.
I already tried setting the ISR priority to low as suggested in various posts...
Hi all,
I installed Nordic examples for Keil MDK, and I am able to compile the examples for the PCA10028 board, which is based on the nRF51422. But I intend to take the...
Hi, I am using 1 central and 2 peripherals. I tried erasing bonding info in both central and peripherals for a few times (by calling pm_peers_delete() in the central and pm_peers_delete...
Hi,
I am using NRF51822 and GCC compiler. I am using softdevice S130. SDK 12.2.
I want to receive the data from Peripheral that is one way only.
I want to use multilink...
Hi everyone, I have one question shown in the title. I try to add a second service in "ble_app_uart" project (the project is in the SDK for nRF51, SD130 v2), I did not change...
Hello,
I was using the nrf24LE1 where i used hal_nrf_set_power_mode() to set the radios' power down mode. Options are power-up and power-down. This is when i was using...
I have a system, with cc2540 as central and n51822 as peripheral with s130. Sometimes while they are close to each other, the connection link gets lost.
I disabled updating...
I'm using SDK14, S132 5.0 and nRF52832, and trying to enable and disable softdevice in my application. In main function, the power management loop is like
while(1)
{...
I am using SEGGER Embedded Studio for developing mesh network on nRF52832. For curiosity I pressed the BOOT/RESET button (SW5) while applying power to the board and it entered...
