Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
My configuration:
NRF51822 v2
TWI
GPIOTE
Issue:
The gpio interrupt does not get triggered. I know that my twi device is changing the state of the gpio3...
Hello, I apologise for this being quite simple as questions go but I was wondering if anyone knew where to begin or if there is any good information out there on how to use...
Hi,
I need use the nrf51822 to connect to PC via usb ble adapter (virtual com port).
The PC side has the USB BLE dongle (adapter).
http://www.amazon.co.uk/Plugable-Bluetooth...
Hi....
Is there any issue in sending a value on a character in button_event_handler? When i tried it disconnection is happening.Am not using button service , just using...
When running the makefiles found in the esb/gcc_rx and esb/gcc_tx folders I get the following errors:
base:gcc_tx jnoble$ make
mkdir _build
"/Users/jnoble/hardware/nrf51822...
I have trouble compiling successfully even the simplest of example codes for the nRF51822 with the Keil MDK-ARM toolchain (v5).
For example, for the "blinky" project, I...
I have ported the example ble_app_beacon from sdk 7.2.0 for use with nrf51422_xxaa and softdevice s310 (v.2.00).
In the function ble_stack_init() there is a call to the...
Hello everyone,
I have two doubts related to pca10001 board:
What is the maximum amount of current
that can be pulled from a single GPIO
pin?
Does the...
Hello,
I just received new rev.3 nrf51822 chips, so I am migrating with my project to newest SDK version.
I installed Keil5 with that smart run-time environment manager...
I would like to send the current status of the battery as a beacon.
ADC and a few resistors and what do I need?
I am currently using nrf51822.
I know nrf51822 to...
I'm trying to port my old project to the newer soft device and SDK (v8.0.0) and just ran into an issue where the app_timer_event_t seems to no longer be defined. My previous...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Is there a UART version of the DFU example that is provided with the new SoftDevice 7.0?
If not how to go about modifying the BLE DFU example to be able to handle UART...
Hi, I made a beacon board only have button and leds. The version of chip is nRF51822-QFAA G0. I used the precompiled hex file in the nRF518222 Beacon v1.1.0. After I download...
Hi,
I am trying to debug a custom PCB for the NRF51822 - I can run a modified version of the HRS application (S110) that has been verified on the PCA10004. The LF clock...
