Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
I have a custom board with an I2C connected sensor ADXL345. I have to do GPI/O initialization to select the I2C. This works because I can read the ADXL with custom I2C commands...
Hi
I am using nrf52840 in my custom board. I have a gpio button which is assigned for as a factory reset button. So when i press the button the whole board needs toi be...
Hello,
we are looking to develop multiple BLE audio source which sends the mic data to the receiver and the receiver receive the audio data from multiple transmitters...
In my design, I aimed to isolate the USB interface. To achieve this, I used the Analog Devices USB isolation chip, ADUM3160BRWZ, to isolate the connection between the PC and...
When I need to switch between 1M and 2M
I create an object of the type bt_conn_le_phy_param and fill in the parameters appropriate to the radio mode I want, and then I call...
Hello,
I would like to know if the nRF9151 is suitable for building a product that will be able to monitor (read) multiple pulse signals originating in utility meters (electric...
We are using nRf5340 and nRf7002. In our application , we are connecting wifi and goes to ksleep for few minutes.
After wake up from the sleep. wifi is not reconnecting...
Hello all,
I ported an old nrf5 application from SDK 12.3 to SDK 17.1. It uses S112 7.3.0 and FreeRTOS. Unfortunately I am getting time variant softdevice hard faults at...
While testing nRF FOTA download library we noticed that it supports only one image update at a time (download image, then reboot).
Irrespective of the image (either application...
Hello, I just upgraded from SDK v2.5.0 to v2.7.0 and now I have a problem updating the bootloader.
In my project I have b0, the mcuboot (in s0 and s1) and the application...
Hello, I followed Getting started guide for the nRF54L15 PDK ( Getting started with the nRF54L15 PDK (nordicsemi.com) ) and bumped into a problem when i try to build "hello...
I am using the following example as a reference for setting the TX power in a peripheral Bluetooth connection: https://github.com/nrfconnect/sdk-zephyr/tree/v3.6.99-ncs2/samples...
Hi, we are doing testing with a Nordic dev kit and looking for ways to check the status of GNSS.
We are becoming familiar with the XGPS command and notifications: docs.nordicsemi...
How can I return from k_sleep (or any other "sleep" method) when an interrupt occurs?
I would like my device to sleep (low power) until a GPIO pin toggles, then wakeup to...
