Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi,
we are now using nRF Toolbox -> Logger tool on our phone to monitor Thingy91 application information via UART/BLE.
Now we would to monitor/log the same information...
Hi,
I am using NCS v2.4.2 and nRF5340DK + nRF21540EK but I can not enable GPIO+SPI mode.
for example, I use nrf/samples/bluetooth/central_and_peripheral_hr application...
I manage to connect to the network and disconnect from it after sending the data, but if I'm in an area without reception, the device tries to connect and after a while, the...
: Chip Not Recognized by J-Link
I need advice from someone familiar with the nRF9160-SICA-B1A-R7.
I purchased an nRF9160-SICA-B1A-R7 chip individually from Digi-Key and...
Dear Sir :
We are now developing on nrf52840, with ncs v2.6.1 and zephyr.
We want to put I2C0 to PM_DEVICE_ACTION_SUSPEND before sys_poweroff().
Our code is below :...
Hello everyone,
I am currently trying to get a ML model running on my nRF52 (preferred nRF52832 but nRF52DK works also for me). Right now I am trying to evaluate if my setup...
We have using nrf5340-nrf7002 in our custom board. SDK version 2.6.1 We understand that the timer will not function in System OFF (deep sleep) mode. However, our project is...
Hi there,
I've encountered a strange PWM behavior and have investigated a bit. When setting load_mode to NRF_PWM_LOAD_WAVE_FORM, creating two sequence, and the latter sequence...
Hello, We want to build our own custom protocol because the features we need are not available from existing protocols like BLE or Zigbee etc. But it is beyond our reach to...
Hi all,
In my application I need to use some of the NET core peripheral from the APP core (since I ran out of peripheral instances in the APP core). According to this page...
I am running into an issue (title), where I am attempting to switch the advertising interval to a slower interval after a set period of advertising in order to save power...
Hello everyone,
I'm trying to test the ble_app_uart example. When I download the code into the 52DK, i can see my device show up as a possible connection, but when i connect...
We have a number of fixtures using nRF52 DK boards to both flash a custom board and to do a DFU operation to that board. We use a SPST switch in the P19 pin 1 lead in the...
Good day
Our custom board contains RS485 implementation. The file schematic for that looks like this:
I have noticed that a driver and sample exists but the driver doesn...
Hello everyone, I'm currently updating my project from SDK v10 with softdevice S110 to SDK v17.1 with softdevice S132 (a huge step). I'm, wondering if what I want my code...
