Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Hello! We are having a problem getting the HFXO to start running in the Murata MBN52832 module (nRF52832-based) so that we can start advertising. The 32MHz crystal is embedded...
I'm having trouble reassigning the pin value for the LED's in the connect SDK. I am using the base PWM Blinky example and have changed the pin value assigned to PWM_LED0 in...
Hi Team,
We would like to connect external LEDs to the NRF52840DK controller.
We could not find any unused GPIO pins to connect.
We have referred manual but it showing...
Hi guys. From the ble_app_hids_keyboard_pca10040_s132 (nRF SDK v17), there were several HID characteristics added.
protocol_mode_char (Protocol Mode characteristics) ...
Hello, Not sure where to direct this (we can open a GitHub issue but wanted to clear it here first), basically everything works great on our Galaxy Tab S6 Lite ( SM-P610)...
Hello,
i am new with the nrf9160, and we are using the download client to download a firmware for a secondary mcu. At the moment its implemented so that at the begin its...
Hello, I recently acquired the thingy53 device and I am trying to use the example of the weather station with matter:
Weather Station . I am following what the documentation...
I've built a simple Matter device for the nRF52840, using the chip-build-nrf-platform Docker image.
The host OS is Linux, and I mapped the physical device ( /dev/ttyACM0...
Dear nordic,
state of your MCUBoot + Immutable bootloader is just awful.
Please fix this hook, when enabled it disables updates of the mcuboot bootloader when used with...
Hi,
From nRF5340 audio example kconfig, there is a note that "now 48kHz is the only sample rate supported". Is this correct? My application would only work for lower bitrate...
Hi,
I have a RIGADO BMD-300 module that can only be accessed over the air. (no physical access)
The modul has the BMDWare ( https://file.elecfans.com/web1/M00/20/D2/oYYBAFmk2JOADMegAAu4fGDEUUo022...
Hello,
I am looking at using the nRF52832 for a safety-related purpose and therefore want to isolate the safety-related code away from the Bluetooth stack. The main concern...
Hi,
I have observed a strange behavior when manually selecting wrong PLMN. I get EMM reject cause 11/PLMN not allowed as expected, but then the modem is stuck in CEREG state...
