Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello,
I am trying to send status messages to a Client model with a specific unicast address on one node. This node's parent element has both generic onoff server and client...
When i define macro
CONFIG_LOG =y
i want to use log
The program can not build successfully
FAILED: zephyr/zephyr_pre0.elf zephyr/zephyr_pre0.map cmd.exe /C "cd...
Hi,
I am trying to send the data received over BLE from nrf5340 to ESP32 and then from ESP32 to nrf5340 using UART communication using below configuration.
nRF5340 esp32...
Hi
I'm wrkig with nRF5 Software Development Kit v17.0.2 and BLE Mesh. When the device is running, after some hours of operation, the NRF_FAULT_ID_APP_MEMACC is getting triggered...
Hi,
I am using nRF connect SDK V2.0.2 chipset 52832 built using VS code.
Need to move the setup from an external clock to an internal RC oscillator.
When I disable ...
The following Pin definitions for QSPI result in Errors during build using NRF Connect SDK. This exact configuration is working on a custom design using nRF5 SDK using the...
I want my client to advertise forever so I added the following code:
static void ble_evt_dispatch(ble_evt_t * p_ble_evt)
{
ble_conn_params_on_ble_evt(p_ble_evt);
ble_nus_on_ble_evt...
Hi,
My device was designed with SDK 15.0, the APP_ADV_DURATION is set to 0 in order to have the device in advertising for all time.
Now I try to use the SDK 15.3 but when...
I've got an embedded application where I want to stream from my device to wireless headphones. Really looking for legacy (I think) right now as I'm not sure LE audio is supported...
I'm getting an occasional MPU fault on the nRF52840 on the Thingy91 when starting scanning:
Running arm-none-eabi-addr2line leads me to
buf->len -= len;
in...
Hi,
I am working on PWM and i am using bellow function for pin set cycles and it's working fine as per Duty cycle and frequency
i am getting the wave form also but i'm...
Hi All,
Is macro in /modules/nrfx/hal/nrf_rtc.h correct?
/** @brief Macro for converting expected frequency to prescaler setting. */
#define RTC_FREQ_TO_PRESCALER...
When compiling without a pm_static.yml in my project and using the dynamic partition resolver with mcuboot I noticed that I get an overflow error.
The current accepted fix...
hello
I am using ufl(U.FL-R-SMT(01)) 50 ohm antenna
My question is: is the matching circuit listed in the picture sufficient or do I need another component
