Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
I'm trying to run the DFU sample l9_e5_sol on a custom board using the nRF5340 and SDK version 3.0.2.
My goal is to perform DFU over BLE using external flash. However, before...
To preface:
Board: nRF9151DK
nRF Connect SDK / Toolchain: 3.1.0
Hello,
I believe I found a bug regarding PSM (Power Save Mode). Specifically, you can't disable...
Starting with the lbs example from lesson l4e2 of BT fundamentals course, I'd like to send an indication similar to the button (and keep the button). I basically created duplicates...
I am using the nRF9151-DK with the standard (from code examples) firmware . When configuring both P0.13 and P0.17 as ADC inputs, I notice that the current consumption on P0...
I am working with the connected_cs examples on the nRF54L15 DK and trying to swap the GAP roles. In my case:
Initiator = GAP Peripheral
Reflector = GAP Central...
I am working on a Bluetooth Low Energy (BLE) project using the nRF52840 Development Kit (DK) , which has been reconfigured to simulate an nRF52805 chip. The firmware is based...
How can you get the simple channel sounding test going with the bluetooth/cs shell commands?
I've got the shell working over UART and devices talking with each other but...
I tried to add external memory to mcuboot. In fact, I have successfully added it in app, but the same configuration seems to have problems in mcuboot ，mcuboot reports an error...
Hi,
We are developing a hardware and software solution for a locator tag using a minimalist approach. We want to use both, the Google Find Hub and Apple Find My Network...
I maintain an nRF52840 project on the legacy nRF5 SDK and am migrating to an nRF54L15 Bare Metal project.
I could not find a bare-metal “radio test” example, so I’m bootstrapping...
I do connect 52840 DK board to PC through USB cable, sine I want to see runtime log. but meanwhile, I want to use PPK2 to see the current of 52840 DK board, Can I get the...
Hi everyone, I noticed something unusual while testing BLE transmission and reception:
Transmitter: nRF5340DK
Receiver setups tested:
config：Target board...
Hi,
If I build the extxip_smp_svr sample app for the nrf5340dk board. The network image firmware version is set to 0.0.0.0.
To reproduce the issue, do the following...
In Lesson-3 Ex-2 for the BLE Fundamentals course, the steps for setting preferred PHY (steps 7 thru 9) is causing fault on my nRF52840-DK board.
Log messages are as follows...
Hi Nordic Team,
I'm currently working on integrating TagoIO using MQTT in our application. While attempting to add the MQTT connection details—specifically the username...
