if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
I have used your example of a bootloader nAN_18. I can create a basic program, with new firmware, and also load my new bootloader program at the high end of memory.
My...
Hello, I am using an nrf52840 with softdevice S140 (7.0.1) configured as GATT client. I successfully write data to the GATT server (Led Button Service) to set the LED using...
Hi,
I'm trying to add a custom service to a working application that has a working battery service.
I have followed https://github.com/NordicPlayground/nRF52-Bluetooth...
Hello.
I am testing UART using ble_nus_data_send function.
However, it has different length data was sending from each trial.(ex. 0, 4095...)
In the ble_nus_data_send...
Hi sir,
I am using ble_app_uart to send the enegry value to the mobile. for energy calculation i am using internal rtc oscillator but after 179 secs the device stops working...
For example, I get logs like this, and I want to know what these events are:
ble_cts_c: BLE event handler called with event 0x57
I also see 0x36, 0x12, etc. when the CTS...
To the kind attention of Nordic support team,
after doing some ble bonding between an nRF52 device and an host computer, I can see this situation in device flash. So, these...
Hello,
I am trying to develop a sensor which can connect to multiple sensors and send the data which is received by its UART through bluetooth, at the peripheral. Central...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
when i copied the spi_fujitsu_fram example to my project folder on c drive, i am getting this error "zephyr/linker.cmd:70 cannot move location counter backwards (from 0000c23c...
Hello!
I would like to know if there is any way to route the signal from the main LED from Nordic Thingy 52. I checked its data sheet and I only found the pinout for other...
After downloading nRF5 SDK v17.0.2, I checked the Release Notes - and they state SES v4.50 has "been used for testing".
So I downloaded & installed SES v4.50
The HID Keyboard...
Hi, recently I want to establish a connection between two development boards (STM32F103 + nRF52840-DK), that the STM32f103 board can create the data and send it to the nRF52840...
Hello, I have a project running on a PCA10040 board, using softdevice 132 (0x9D, v5.0), ble and serial port for data transfer.
I want to migrate this project from this...
I am trying to use the UART for a custom version of the DFU. I have it transmitting no problem, but I never get the RX_DONE event. I cannot see any reason and I have looked...
