I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Hi,
I use a GPS Modul to send data via uart to the NRF 51 and then I send the string via SPI and fatfs to the SD CArd.
I see the LED4 blinking and during the debugging...
Hi,
I was trying nrf5-mpu-simple example with MPU9250 - SDK 14.2.0, it is giving me x, y & z axis values.
When I try WHO_AM_I with it, I am unable to do so. I have added...
Hi, I am try my first code by follow this website
https://devzone.nordicsemi.com/b/blog/posts/segger-embedded-studio-a-cross-platform-ide
, and step by step.
When...
As we all know,the examples of NRF51 SDK 11 about DFU is all using Device manager,do you have some example about Peer manager?
I am very looking forward to see the example...
hi , now I am using nrf52832 base on the sdk 14 to develop our location system, the ibeacon around my nrf52832 circuit board will advertise every 500ms, and the parameters...
My device is entering DFU mode, staying there for a few seconds, then shutting down. I'm trying to figure out a good way to figure out if it's a watchdog issue or a power...
Hi.. I am still new in using nrf product and understanding the example given via SDK. For my project, I am trying to send continous data via BLE app UART to mobile phone....
Hi,
As a part of settings up an automatic BLE DFU testing environment, we're trying to update a single NRF52 board using a PC connected to a NRF51 dongle.
The dongle is...
Hi,
I am using Sunding-515 cycling speed and cadence sensor it’s data is broadcasted as per the GATT characteristics. We have already done the data parsing in our other...
In SDK 15.0.0\modules\nrfx\soc\nrfx_irqs_nrf52810.h, at line 65,( link ) it defines a SPI1 compenent:
But 52810 spec( link ) mentions only SPI0.
Is the code file correct...
Hello everyone,
So I'm trying to maybe start get going with the NRF52832 platform but every time I try I get stuck with it.
In this example I'd like to use different...
Hello, I would like to know if there is there a "global" sdk_config.h file which has #defines for all modules? Ie, if I make my own project, and use this file, all I would...
Hi!
I would like create my own application of BLE Mesh on nRF52832, I had gone through the Light switch example and understood some basic concepts and now i'm thinking start...
Hi,
I tried to erase the bound and start another pairing procedure without rebooting my device. I was not able to remove the bond correctly. The system hangs when I call...
