Hi..... This is Venkatesh. I am using nRF52-DK Evaluation kit. This is my first question posting here. It is pleasure to have an account to share my knowledge and get the...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
I am in the process of integrating a custom display driver (ST7305) into my Zephyr-based project and have followed the necessary steps:
Placed the .c and .h source files...
I'm using SDK version 2.9.0 with an nRF52840 in a combined peripheral / central application.
The nRF52840 device starts advertising, but then after connecting (as a peripheral...
Hi,
I am trying to download the nrf connect toolchain in vs code but getting this error
Error: Failed with exit code 1. Failed to download toolchain bundle Caused by...
Hello.
I am developing an application based on IOS-nRF-Mesh-Library, and currently considering porting firmware upgrade function of IOS-nRF-Connect-Device-Manager for updating...
Dear All:
I don't have a le audio enabled phone, and i want to study the hci commands about cis and bis setup up processure.
Could you please provide some HCI logs from...
Hello there!
I'm trying to run the official, unmodified, version of the `WiFi Shell` sample targeting the `nrf7002dk/nrf5340/cpuapp` board and am currently getting:
...
Dear,
I recently upgraded my project from NCS 2.4.0 to NCS 2.9.0 and encountered an issue with the ST7789V display driver.
Previously, I used SPI0 to interface with the...
Hello, my application is running on a custom board. The BLE Host is on an nRF9160, the BLE Controller is on an nRF52820, and the SoCs are connected via UART. On my original...
Hello,
I am new to multicore programming. I tried to find without much success a complete VS Code sample project from Nordic targeting nrf5340 two cores; ideally with the...
I am attempting to connect my nrf52840/52811 DK to my custom PCB that contains nrf52840. The DK users guide describe the connections on the P19 debug out port but I can see...
Hi all,
This is for nrf9160 with firmware version 1.3.1.
I 'm trying to read back the certificates and comparing with a known CRC.
modem_key_mgmt_read is able to read...
Our system is composed of a nrf5340, a QSPI flash, and a nrf7002 on single wire SPI. We are not using the network processor.
We are using Zephyr NCS 2.9 with sysbuild. We...
I am testing the Sleep idle current for the nRF52833QDAA module.
The module is nothing connected outside except the fundamental circuit as the attached picture shown.
...
Hello,
We have the nRF52833 included in a new PCB design. So far it works well using mcuboot and a UART interface.
I'm trying to get the radio set up and running, and...
NCS: v2.7.0 nRFCloud/utils: a2db3ffedbda237f9c1efb7a68ec2d270c346e56 Hardware: Custom Board with nRF9161 I am writing a provisioning automation (with robotframework), but...
