I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Hello,
I use nrf51822 as peripheral and after connection with central module(nrf51422 dongle) I want to set a period(10 s or more than 10 s) in which Softdevice will have...
Hi,
I have already read several posts and articles about how to maximize data throughput on Bluetooth Smart (like sending multiple Notify packets with 20 bytes of data...
Hello,
How can I port the code written for nRF51 to nRF52 in Keil IDE.
Also, I see that Keil supports nrf52 but does not provide device specific software packs.
Is...
I want to use the automated test function of the master control panel.
I want to test the device information service and wrote this xml script to connect to the target...
Hi there,
How could I receive a large data from phone, example 120 bytes from a characteristic. So far I was able to receive 20 bytes.
From the working code of 20 bytes...
Hi
Try to send characteristic notification by invoking sd_ble_gatts_hvx() with the following parameters:
uint32_t err_code = NRF_SUCCESS;
ble_gatts_hvx_params_t params;...
I do run the “nrfjprog --pinreset”,later, the nrfjprog can not find the nrf51 device,WHY?
the nrfprog version is V5.2.0,
I use nrf51822qfaa,s110,keil,etc.
Hi, Guys,
I have a question about chip operation temperature. Will the chip auto reset when the temperature over 75 C? I checked the nRF51822 product specification v3.1...
I would like to learn more about when it is safe to invoke soft device methods and when it is not. For example, are the following 'allowed' to make soft device calls to update...
Update to below: I get data out of the VCP and into Termite for a sub-second when I first power the board (with handshaking enabled), then I get no subsequent data (even though...
Hi,
I have just received a bunch of N550 modules and now I want to try and see if it is possible to update the firmware of these devices without using a JTAG.
If I understand...
I wrote my own ACI interfacing code, so I have questions about some details of the data credit system that most devs may be insulated from by the Nordic SDK.
Section 25...
Hi All,
I was wondering if it was possible to program the nrf51x22 in c++? I am using Keil and I'm trying to convert the examples in the SDK to CPP by adding --cpp to the...
hi,
I have used sd_flash_write() in my code. The scenario is that sd_flash_write() will be called after a DISCONNECT event. And it would wait for system events :
NRF_EVT_FLASH_OPERATION_SUCCESS...
Running S120 2.0 central on nRF51422 QFAAE0 (1504CH) and when I call scan_start() i'm getting 0xDEADBEEF at line 431 in file src\ll_lm.m0.c"
Can anybody shed some light on...
