if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
I have used your example of a bootloader nAN_18. I can create a basic program, with new firmware, and also load my new bootloader program at the high end of memory.
My...
We have developed a custom board based on the nRF52840-CKAA-R7.
Development is well into the re-release phase, and I am having some issues with battery life.
I've done...
Hi,
I have a mass storage that format a fat_fs volume and create a file when I plug the device by USB. Here is how I create a file :
It works fine, and I can see my...
Good morning,
I am developing my Zephyr solution with a Supported board RAK4631 in a RAKWireless solution called Wisblock. This is a kind of building blocks called Wisblock...
Hi,
I have the unfortunate task of needing to update a significant amount of inventory (several thousand units) using BLE OTA.
The devices are using the nRF52805 with...
Hello, I am currently developing a program that uses two SPI interfaces with the nRF5340DK. I want to use SPI3 and SPI4 for two different modules. SPI4 works fine and I can...
There are some fields that I wish to change. I am using the project direction_finding_connectionless_rx as a base to work with. I would like to be able to read and write specifically...
uart:~$ wifi_radio_ficr_prog otp_write_params 0x120 0xff63ec4f 0x9fff OTP Region is open for R/W Invalid MAC address. MAC address cannot be all 0's, broadcast or multicast...
I have a device on my desk that performs the data transfer I need, so I know it's possible. I've attached a screenshot of the successful data transfer.
I tried to replicate...
I have two toolchains and two nrf SDKs installed. v2.4.1 and v2.6.1.
I could change the toolchain used from vs code extension, but I couldn't change the west workspace....
I have been sitting with this problem for almost 2 weeks and have tried alot of different thing but without anything working,
Im using VS code with the nrf9161 and it has...
We have tried the following changes, but couldn't get expecting results.
Sometimes unable to pair two devices / Sometimes fails to link with one device
Could you answer...
I am using mbedtls to parse a certificate. The code is as follows:
It builds successfully but when I flash I get the following error:
Failed to parse certificate: -9774...
I'm trying to setup so that I can do firmware update on nRF5340 using only the internal flash. Due to the many dependencies between different images I'm creating my custom...
hi support team,
i was tesing homekit ncs2.5.3, with iphone se ios18, pairing failed, and i use another two iphone 12, they all succeed.
i can't see why the ios would...
USING THE PERIPHERAL_UART TO CONNECT WITH THE MULTIPLE CENTRAL DEVICES . I MODIFIED SOME CODE AND ADDED THE CUSTOM DATA WHICH IS HAVING THE 5 BYTES. WHEN I USE TO FLASH THE...
